Does anyone have the floorboard drawings for the -12 or blueprints? Univair nor Clyde Smith has them. I don’t believe the cub club does either.
Does anyone have the floorboard drawings for the -12 or blueprints? Univair nor Clyde Smith has them. I don’t believe the cub club does either.
Last edited by nbills77; 12-03-2019 at 10:03 PM.
http://www.supercubproject.com/drawings/main.aspx
Sent from my iPhone using SuperCub.Org mobile app
Deleted FaceBook, join me at https://www.mewe.com/i/mikeskup
Videos http://www.youtube.com/user/mcsrepair https://www.youtube.com/channel/UCIk...C-rmr3wpSuMT8g Pictures https://photos.google.com www.mcsrepair.com
www.SkupTech.com
Sent from my iPhone using SuperCub.Org mobile app
Deleted FaceBook, join me at https://www.mewe.com/i/mikeskup
Videos http://www.youtube.com/user/mcsrepair https://www.youtube.com/channel/UCIk...C-rmr3wpSuMT8g Pictures https://photos.google.com www.mcsrepair.com
www.SkupTech.com
I could take some rough measurements for you. That would give you a place to start. -12s all seem to be a bit different from one to the next. I also noticed that mine are not symmetrical from side to side.
Wayne
mike mcs repair liked this post
Oops. I missed the-12 part
Sent from my iPhone using SuperCub.Org
Deleted FaceBook, join me at https://www.mewe.com/i/mikeskup
Videos http://www.youtube.com/user/mcsrepair https://www.youtube.com/channel/UCIk...C-rmr3wpSuMT8g Pictures https://photos.google.com www.mcsrepair.com
www.SkupTech.com
I appreciate amy help. Rough measurements would be a great start.
Ill start off with a a few pictures. These are my floorboards as I was disassembling my -12. Note the reinforcement for the front brakes is missing. The interior fabric is wrapped around the outside of the longerons.
![]()
![]()
![]()
![]()
![]()
![]()
The floor doesn't touch the longerons but is fully supported on the diagonals and cross tubes. The dimensions and diagrams I have are at the hangar. I may be there later this week or early next week and will grab them for you.
Wayne
Even with dimensions you will still end up using poster board and foam board to build templates. And lots of duct tape. Or trace the ones you remove. FA Dodge sells a brake reinforcing bracket for the 12 that goes under the front floor board
mike mcs repair liked this post
pictures here of my versions.... like others have said you just wing it and improve on the originals.....
https://goo.gl/photos/PuiR5ha2aBDbkUBS8
Deleted FaceBook, join me at https://www.mewe.com/i/mikeskup
Videos http://www.youtube.com/user/mcsrepair https://www.youtube.com/channel/UCIk...C-rmr3wpSuMT8g Pictures https://photos.google.com www.mcsrepair.com
www.SkupTech.com
Mike those stiffener blocks that are on the bottom of the floor in your pics are those original?
Sorry for the delay, but life and weather have delayed my attempts to get the dimensions for the floorboards.
The aft floor is about 30" wide and 29" front to back. The front and back floors butt at the cross member under the truss.
The stiffeners are more like spacers that support the floor on the cross members and diagonals.
The ones on my floor are about 3/4" square.
as jrb said, start with posterboard or, cheap 1/4" strips of plywood and some hot glue and make a template from your airframe. YMMV.
Wayne
Bookmarks