I'm on a quest.
I need a (one) 2" OD aluminum tubing Y fitting for a heater experiment anyone know where I can get just one or two?
Thanks
Kirby
I'm on a quest.
I need a (one) 2" OD aluminum tubing Y fitting for a heater experiment anyone know where I can get just one or two?
Thanks
Kirby
Remember, These are the Good old Days!
Glen,
My bad, I should have better described it. I'm looking for a symmetric Y so flow (would be flowing up in this context) will split evenly to the two branches and discharge at the same angle from the main leg.
Kirby
Last edited by OLDCROWE; 11-04-2019 at 04:36 PM.
Remember, These are the Good old Days!
Kirby if you find one let me know. I looked for the same a few years back and all I found was plastic. After a number of heat cycles I discovered my heater output was greater than I envisioned, and the reason they use aluminum. Never bothered to fabricate one, but that was the next direction.
pb
I used the type I posted in my J4 heat 10 years ago so that heat came out under panel in front of both sticks. The drag inside the scat tubing must balance it out because both deliver the same amount of heat
Glenn
"Optimism is going after Moby Dick in a rowboat and taking the tartar sauce with you!"
I have the one Glenn posted and a scat house hooked up the rear torque tube. The heater no longer melts one foot with the y attached
Sent from my iPhone using Tapatalk
https://www.supercub.org/forum/showt...-heat-vent-mod
Sent from my iPhone using Tapatalk
Atlee has them as part of their defrost kit. Not sure if he’d sell separate. http://www.fadodge.com/universal-defroster-kit/
Sent from my iPhone using SuperCub.Org
Deleted FaceBook, join me at https://www.mewe.com/i/mikeskup
Videos http://www.youtube.com/user/mcsrepair https://www.youtube.com/channel/UCIk...C-rmr3wpSuMT8g Pictures https://photos.google.com www.mcsrepair.com
www.SkupTech.com
Maybe here?? https://www.summitracing.com/parts/sum-991104/
Sent from my iPhone using SuperCub.Org
Deleted FaceBook, join me at https://www.mewe.com/i/mikeskup
Videos http://www.youtube.com/user/mcsrepair https://www.youtube.com/channel/UCIk...C-rmr3wpSuMT8g Pictures https://photos.google.com www.mcsrepair.com
www.SkupTech.com
"Optimism is going after Moby Dick in a rowboat and taking the tartar sauce with you!"irishfield thanked for this post
RaisedByWolves liked this post
I have a Tee...![]()
mike mcs repair liked this post
buy some 2 inch tubing, and find a guy that tig welds.![]()
Last edited by tempdoug; 11-05-2019 at 01:48 AM.
skywagon8a liked this post
I can make you one, I might have one in my box of SCAT hose parts.
"Optimism is going after Moby Dick in a rowboat and taking the tartar sauce with you!"
glenn, ive made up my mind im going to do one like yours, but where that bottom piece can just slide down into a couple of grooves. got to make the bracket. for easy in easy out. even the top tee just going to make out of 2 inch aluminum.
Steve Pierce
Everybody is ignorant, only on different subjects.
Will Rogersmike mcs repair liked this post
First attach this to cabin side of heat box
The right side of this Y has a belled end that will slip offer first fitting, screw it on or a hose clamp works
Or this one will also slip over first fitting or other 2 outlets of Y
First 2 fitting were from Wag, last one from ACS
When I first mounted the heat up under panel I did a single outlet in front of the stick, it was so hot ( even at zero) I had to wear a glove on my stick hand, changed it to 2 outlets
Glenn
Last edited by cubdriver2; 11-05-2019 at 10:19 AM.
"Optimism is going after Moby Dick in a rowboat and taking the tartar sauce with you!"OLDCROWE thanked for this post
TurboBeaver liked this post
Tgskillskill liked this post
putting one of these down at the cab heat exit at the bottom of the V would even help to get the air to go up and around. just need to point it up at maybe a 45 from the floorboards.
I got stuck in the back seat on the way to your flyin and had the SCAT hose run under the seat and hook on the seat pocket. It was to hot to hold and just kept part of my warm until I looked it back under the seat pointing forward just below the seat base. It evened out the heat throughout the entire cockpit.
This evens out the heat in the front pretty good and the long scat can be put in your jacket when you don’t have a back seater.
Sent from my iPhone using Tapatalk
That’s the same fitting I have laying around. Kirby, send me your address!
On another tread here that I can’t find now , there was a place that made scat with doubled ends... I did an experiment to see if I could do it. I used silicone 2 part liquid for mold making to glue the piece on. It worked. Then I got thinking I bet you can do the same to just make the hose y joint without the aluminum. Still need to test. But I’m sure it will work after first test.
Sent from my iPhone using SuperCub.Org
Deleted FaceBook, join me at https://www.mewe.com/i/mikeskup
Videos http://www.youtube.com/user/mcsrepair https://www.youtube.com/channel/UCIk...C-rmr3wpSuMT8g Pictures https://photos.google.com www.mcsrepair.com
www.SkupTech.comRVBottomly liked this post
Bookmarks