Search:

Type: Posts; User: mike mcs repair

Page 1 of 20 1 2 3 4

Search: Search took 0.18 seconds.

  1. Replies
    18
    Views
    611

    I didnít know cabane v varied? Shock struts and...

    I didnít know cabane v varied? Shock struts and legs did on extended gear, length & width(stance?)


    Sent from my iPhone using SuperCub.Org
  2. Thread: Drones

    by mike mcs repair
    Replies
    192
    Views
    80,680

    https://abcnews.go.com/US/wireStory/faa-approves-f...

    https://abcnews.go.com/US/wireStory/faa-approves-fully-automated-commercial-drone-flights-75287845


    Sent from my iPhone using SuperCub.Org
  3. PA-12 standard landing gear legs drawings with dimensions

    Go anyway

    What country do you live in?


    Sent from my iPhone using SuperCub.Org mobile app
  4. Replies
    18
    Views
    611

    used to only be $300 in early 90's.... and a...

    used to only be $300 in early 90's.... and a brand new factory cub was only $36000 in the 80's....
  5. Turn off your TV and radio. Go out and Live you...

    Turn off your TV and radio. Go out and Live you life. Havenít owned a tv in??? 12? Years(except used as a computer monitor) and havenít turned radio on since mid March when the bs started. Deleted...
  6. Replies
    37
    Views
    1,566

    Never squared off wings without lengthening...

    Never squared off wings without lengthening ailerons or moving them out. But have been hired to make wings back to round wings after severe crashes from lack of aileron control on squared off wings. ...
  7. Replies
    18
    Views
    611

    Replace it Sent from my iPhone using...

    Replace it


    Sent from my iPhone using SuperCub.Org mobile app
  8. http://www.supercubproject.com/drawings/pdfs/A3310...

    http://www.supercubproject.com/drawings/pdfs/A3310015.pdf

    And add LE to spinner distance.


    Sent from my iPhone using SuperCub.Org
  9. Burl sells it all drilled for trim pin use. ...

    Burl sells it all drilled for trim pin use. Burlac.com


    Sent from my iPhone using SuperCub.Org
  10. Replies
    8
    Views
    740

    I know Reeve Airmotive up here in Anchorage used...

    I know Reeve Airmotive up here in Anchorage used to carry them, not sure if they still do, as they quit carrying allot of useful parts after they were bought out....
  11. Replies
    8
    Views
    740

    I thought Iíd seen them on spruce. But canít seem...

    I thought Iíd seen them on spruce. But canít seem to find them at moment searching there... since I donít know their search term!!


    Sent from my iPhone using SuperCub.Org mobile app
  12. Replies
    23
    Views
    905

    My shop project. Not a customer project yet. ...

    My shop project. Not a customer project yet. Still practicing


    Sent from my iPhone using SuperCub.Org mobile app
  13. Replies
    23
    Views
    905

    Stewart System review

    Clocks ticking on your bill at $1.50 a minute......


    Sent from my iPhone using SuperCub.Org mobile app
  14. enjoy cabin quarantining!!

    enjoy cabin quarantining!!
  15. Replies
    22
    Views
    1,075

    EXCEPT, that leave out the VERY IMPORTANT FIRST...

    EXCEPT, that leave out the VERY IMPORTANT FIRST STEP, level plane SIDE TO SIDE using front spar carry through spar(or floor if plane was NEVER wrecked.....) before doing the dihedral measurements...
  16. Replies
    22
    Views
    1,075

    Yes the original rigging instructions Service...

    Yes the original rigging instructions Service bulletin. It think Univair has it online?.


    Sent from my iPhone using SuperCub.Org mobile app
  17. Wing Inter-Rib Bracing...What to do???

    .020Ē 2024T3 is what Univair uses for leading edge skins.


    Sent from my iPhone using SuperCub.Org
  18. Replies
    37
    Views
    1,566

    Think we always used just #6 pk screws for...

    Think we always used just #6 pk screws for installing tips. No need to get any bigger or nut plates. You will have many screws holding on the tips


    Sent from my iPhone using SuperCub.Org
  19. Replies
    22
    Views
    1,075

    Dihedral question

    Rerig per book. I use front carry through spar as sideways level point.

    Also once you have fuselage level sideways, if you have a turn and bank or just a ball, center the ball now by rotating...
  20. Replies
    18
    Views
    1,268

    Low cost seat cover solution?

    Google ďfur sewing machineĒ they have a separate function/move to them to pull the hairs out of sewn seam before stiching. I forget the exact name, I have one in garage. Bonis?? Brand??

    Like...
  21. More for practice anodizing..... finally getting...

    More for practice anodizing..... finally getting titanium spring holders made that are reliable. Thatís been my biggest problem. And to get it to JUST be a side job while I do other work. And just...
  22. Replies
    7
    Views
    649

    I Donít install them since I use aluminum for the...

    I Donít install them since I use aluminum for the floor boards


    Sent from my iPhone using SuperCub.Org
  23. 535415354253543535445354553546535475354853549 ...

    535415354253543535445354553546535475354853549

    A little why not project


    Sent from my iPhone using SuperCub.Org mobile app
  24. yes, and screw to spar with the AN530 screws,...

    yes, and screw to spar with the AN530 screws, and normal screws or (pop?)rivets to top skin
  25. Replies
    13
    Views
    784

    Plug cleaners

    Also reminds me of the (opposite) lack of logic when I was 17 and worked at the school doing maintenance. I was payed $15 hour but we would spend a half hour cleaning the paint rollers that only...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4