Search:

Type: Posts; User: Gordon Misch

Page 1 of 20 1 2 3 4

Search: Search took 0.10 seconds.

  1. Replies
    6
    Views
    461

    I used hat-type stringers, mounted similar to how...

    I used hat-type stringers, mounted similar to how Stinson did it. super-12.com. Steve has 'em, near Chehalis.
  2. Replies
    77
    Views
    5,731

    He was mostly just razzing me. Though that...

    He was mostly just razzing me. Though that particular time I WAS way too high and had to slip aggressively.


    Agree. End up going faster than otherwise, but total energy is dissipated...
  3. Replies
    33
    Views
    6,468

    Right. Valid for constant acceleration only. ...

    Right. Valid for constant acceleration only. Not even exact on wheels because drag increases with speed.
  4. Replies
    55
    Views
    5,654

    JIC fittings from a hydraulics shop will work if...

    JIC fittings from a hydraulics shop will work if AN fittings not available. They're 37 deg. The automotive SAE flare is 45 deg.

    Here's more than you ever wanted to know about that: ...
  5. Replies
    20
    Views
    943

    On my -12 the bottom of the stick where the...

    On my -12 the bottom of the stick where the aileron cables attach is extended by an inch or so. It's a bolt-on piece, and operates to give more cable travel for a given stick deflection. I don't...
  6. Thread: Cub Jigs

    by Gordon Misch
    Replies
    26
    Views
    2,891

    Maybe. Depends on the cold stress. If in...

    Maybe. Depends on the cold stress. If in tension or neutral, yes, it will pull. If in compression, maybe just relax the joint.
  7. Replies
    4
    Views
    452

    I have a couple spare cable-safes - I'll give em...

    I have a couple spare cable-safes - I'll give em to you if you want em.
  8. Replies
    17
    Views
    1,248

    Sticky: Now Perry, nice is good.

    Now Perry, nice is good.
  9. Replies
    76
    Views
    5,294

    Ugh, that is a genuine PIA. Kinda like getting...

    Ugh, that is a genuine PIA. Kinda like getting Clydsdales to pull a real load. 8)

    FWIW I have a pic somewhere of a Clyde standing on a sled being pulled by - I can't remember - Belgians,...
  10. Replies
    9
    Views
    591

    Just finished (I hope!) Going through that. My...

    Just finished (I hope!) Going through that. My MA4SPA carb started dripping last summer, stopped for a while, then got worse. I have overhaul paperwork from Avstar, 2011. About 700 hours sunce...
  11. Replies
    2,141
    Views
    548,437

    https://www.adn.com/alaska-news/aviation/2021/02/0...

    https://www.adn.com/alaska-news/aviation/2021/02/05/ntsb-plane-that-crashed-near-wrangell-st-elias-national-park-killing-2-apparently-broke-up-in-midair/
  12. Replies
    90
    Views
    40,794

    I have the short mount on my -12, and Sutton...

    I have the short mount on my -12, and Sutton exhaust. It all fits fine. Enjoy!
  13. Replies
    90
    Views
    40,794

    The entire system is forward of the accessory...

    The entire system is forward of the accessory case, so the mount shouldn't matter.
  14. Replies
    27
    Views
    6,352

    Good point for annual insp - fuel valve screws...

    Good point for annual insp - fuel valve screws tight! Thanks for the reminder - - -
  15. Replies
    402
    Views
    80,680

    Bushings would be pressed into the outer tube. ...

    Bushings would be pressed into the outer tube.

    Along the lines of what Sky was saying, you don't want too close a fit between inner and outer tubes. If too close it wouldn't take much to get...
  16. Replies
    402
    Views
    80,680

    Give some thought to material removal - and - how...

    Give some thought to material removal - and - how much is left in that outer tube. Another possibility would be to drive a hardened bullet through that outer tube, with heat on the outer tube if...
  17. Thread: 65 died

    by Gordon Misch
    Replies
    45
    Views
    3,197

    Thawed ice? Or the opposite, freezing water in...

    Thawed ice? Or the opposite, freezing water in the fuel line?
  18. Replies
    8
    Views
    450

    Well, the obvious found its way right past me -...

    Well, the obvious found its way right past me - again. I squirted a dab of LPS2 into the keyhole, and it works much, much better now. Thanks folks!
  19. Replies
    8
    Views
    450

    Dunno. I'll try some oil first, as Irishfield...

    Dunno. I'll try some oil first, as Irishfield suggested.
  20. Replies
    8
    Views
    450

    Thanks - I haven't been able to locate a parts...

    Thanks - I haven't been able to locate a parts kit that includes the keylock portion. Just contacts etc.
  21. Replies
    8
    Views
    450

    Bendix Ignition Switch Repair?

    I have a Bendix switch (no start position) that is probably original on my -12. It's getting so that I have to jiggle the key just right to get it from the off position. I bought a new key, based...
  22. This sure seems like the best approach.

    This sure seems like the best approach.
  23. Replies
    16
    Views
    8,766

    I had a leak that I would have sworn was oil...

    I had a leak that I would have sworn was oil cooler or case parting-line related, but turned out it was a tiny crack in the engine case. The powder test would at least confirm or refute an external...
  24. Replies
    16
    Views
    8,766

    One thought - - clean the engine thoroughly...

    One thought - - clean the engine thoroughly with solvent and let it dry. Spray suspect areas with dye penetrant developer powder, run engine until source appears. I've read a simpler way here,...
  25. Replies
    36
    Views
    2,631

    Yes, however the heat path thru the crankshaft...

    Yes, however the heat path thru the crankshaft cross section to the prop is small by comparison. Heat flow rate varies directly as cross section and inversely as the length of the conductor - in...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4