Search:

Type: Posts; User: Mr. Ed

Page 1 of 6 1 2 3 4

Search: Search took 0.40 seconds.

  1. Replies
    54
    Views
    4,662

    Not Spruces fault but typical of the USPS lately....

    Not Spruces fault but typical of the USPS lately. I’ve had regular mail take 16 days when it took 3 in the past. Ordered stuff from Spruce that was shipped on the 11th from Corona, CA. Arrived...
  2. Replies
    127
    Views
    26,614

    5668756688 made a carbon fiber flange that...

    5668756688

    made a carbon fiber flange that bonds to the floor around the aft control stick. Snaps are pop riveted to the lip, a leather boot was stitched to fit and snaps into place. Hopefully...
  3. Replies
    16
    Views
    1,056

    Some builders donít install the D window at all...

    Some builders donít install the D window at all because you really donít look out them much at all. Those without D windows sometimes paint a window on just for esthetics. Way too much hassle to...
  4. If you rent from Home Depot the allowed mileage...

    If you rent from Home Depot the allowed mileage won’t get you to the edge of town and back. After that you’re paying very high mileage charges. I’d watch out for that with Uhaul too.
  5. Replies
    127
    Views
    26,614

    55904 panel layout......just stickers at this...

    55904
    panel layout......just stickers at this point but components are being ordered. Dynon 10” HDX, radio & intercom, AV-30, Avidyne 410 GPS navigator. Switches will be located on the angled...
  6. 55559

    55559
  7. Replies
    127
    Views
    26,614

    Pulled the under seat storage box off the mold...

    Pulled the under seat storage box off the mold today. Didn’t turn out great but it’s acceptable. I used 2” pink foam board to make the mold. Under vacuum the ends of the foam board compressed a...
  8. Replies
    127
    Views
    26,614

    I tried my first three dimensional carbon fiber...

    I tried my first three dimensional carbon fiber piece. It snaps over the cargo door sill and covers the rudder cable and a pulley below the door. Fabric will wrap over the sill so I put 8 layers of...
  9. Replies
    127
    Views
    26,614

    Still working on the carbon fiber floor. I made...

    Still working on the carbon fiber floor. I made carbon fiber 3/4”x3/4” angle, 13’ of it, cut it into smaller pieces and bonded those to the floor sections using West Systems Six-10 epoxy. The...
  10. Replies
    13
    Views
    1,386

    Check Professional Plastics. They had 4’x8’...

    Check Professional Plastics. They had 4’x8’ sheets of Kydex in a number of colors. I went went with a light gray for the lower half of the sidewalls and a white for the upper and ceiling sections. ...
  11. Replies
    40
    Views
    2,368

    Mounting the antenna straight up is one thing but...

    Mounting the antenna straight up is one thing but when was the last time you saw a wreck that crashed in a way that left the antenna straight up? Not trying to start an argument here, just curious...
  12. Replies
    127
    Views
    26,614

    54977 Finished the cargo area floor. The hole...

    54977
    Finished the cargo area floor. The hole is an access panel for elevator cable pulleys. It now has a CF cover plate. On the list for interior CF is the under seat storage bin, fuel selector...
  13. Replies
    127
    Views
    26,614

    No skill, just hours of YouTube University study...

    No skill, just hours of YouTube University study and a phone consultation with Ted Waltman.
  14. Thread: Oiling tubes

    by Mr. Ed
    Replies
    8
    Views
    943

    If TubeSeal is available from Spruce they are...

    If TubeSeal is available from Spruce they are hiding it well. I have corrosion X so I’ll use that.

    I do plan to put it on floats so want that extra layer of protection. I built in a provision...
  15. Replies
    127
    Views
    26,614

    I laid up and vacuum bagged the forward two...

    I laid up and vacuum bagged the forward two carbon fiber floor panels yesterday. Pulled them off the table this morning and spent the rest of the day trimming and fitting them into position. Still...
  16. Thread: Oiling tubes

    by Mr. Ed
    Replies
    8
    Views
    943

    Oiling tubes

    I searched the site for information on oiling the tubes and it sounds like TubeSeal is the desired product. However, when clicking on the links (all from old posts), searching the internet,...
  17. Steve, How thick is that aluminum ventral fin...

    Steve,

    How thick is that aluminum ventral fin in the photo you posted?
  18. Thread: Montana floats

    by Mr. Ed
    Replies
    25
    Views
    2,912

    Received this today from Montana Float Co.: We...

    Received this today from Montana Float Co.:
    We have only put our 2400's on a Smith Cub and a Northstar Cub which may be too much for a PA-18.
    Our 2200's built are $43,300. The kit is $27,800.
    The...
  19. Thread: Montana floats

    by Mr. Ed
    Replies
    25
    Views
    2,912

    Montana floats

    Does anybody know the status of the Montana Float company?

    I plan to put my experimental PA18 on amphibious floats in a year or two. There are some positive comments about them on this site but...
  20. Replies
    7
    Views
    880

    I have a Precision Airmotive Silver Hawk servo. ...

    I have a Precision Airmotive Silver Hawk servo. I haven’t read through the manual yet so don’t know if they recommend turning the fuel off after shutdown.
  21. Replies
    7
    Views
    880

    Fuel selector valve

    Iím starting to run fuel lines in my experimental PA18. Running a Titan Extreme 340, fuel injected, headerless fuel system. What Iím looking for is input on fuel selector valves. I know Dakota Cub...
  22. Replies
    127
    Views
    26,614

    Prep process was glass bead blasting, clean with...

    Prep process was glass bead blasting, clean with compressed air, primer, black then clear powder. Owner says they do 20 to 30 per year.
  23. Replies
    127
    Views
    26,614

    I got a good look at the float fittings today and...

    I got a good look at the float fittings today and found one spot on one side deep in that angle that looks a bit thin. Everything else looks good. I’ll use an airbrush to coat the thin spot.
  24. Replies
    127
    Views
    26,614

    Steve, Thanks for the heads up. That’s a...

    Steve,
    Thanks for the heads up. That’s a really tight angle so I can see how it might get missed. I’ll look it over and report back.
  25. Replies
    127
    Views
    26,614

    5463754638 Got my airframe and all associated...

    5463754638

    Got my airframe and all associated parts back from powder coat today. I think they did a great job. I haven’t found any spots that were missed. Business name is All Resistant...
Results 1 to 25 of 150
Page 1 of 6 1 2 3 4