Search:

Type: Posts; User: astjp2

Page 1 of 15 1 2 3 4

Search: Search took 0.05 seconds.

  1. Replies
    27
    Views
    1,666

    Are there any sodium filled exhaust valves for...

    Are there any sodium filled exhaust valves for small continentals? ECI used to have a rotator in their 200/300 cylinders, no longer available but I am curious about finding any improvements for the...
  2. Replies
    840
    Views
    521,065

    I just slide it in, the phillips bottle will not...

    I just slide it in, the phillips bottle will not let it spill, I used to just screw in the 15W50 bottle but there was always a chance to spill if not careful, now its not an issue.
  3. Replies
    840
    Views
    521,065

    Best funnel ever!

    Best funnel ever!
  4. Replies
    840
    Views
    521,065

    spruce does it in Arizona, just need to give them...

    spruce does it in Arizona, just need to give them the lengths and prices are not horrible...
  5. Replies
    840
    Views
    521,065

    Yes, I had a can and it would evaporate before I...

    Yes, I had a can and it would evaporate before I would get 2-3 seals done or the lid would get stuck. tubes are cleaner and I can stock 5-6 and always have fresh glue on the shelf.
  6. Replies
    840
    Views
    521,065

    Better shelf life in the tube, mcmaster has it

    Better shelf life in the tube, mcmaster has it
  7. Replies
    840
    Views
    521,065

    When using pliobond 20 in the tubes, I have...

    When using pliobond 20 in the tubes, I have found that you need to use the whole tube, mix and then coat the crank seal because it separates in the tube and the tube splits long before you can get...
  8. Replies
    840
    Views
    521,065

    Good screws for the engine compartment adel...

    Good screws for the engine compartment adel clamps, not cheap but a super time saver because they have a reduced head size. Mostly need #10 and use mostly 5/8Ē long or longer with ms21042-L3 nuts....
  9. Replies
    34
    Views
    16,400

    I flew the trench in an o-200 powered Taylorcraft...

    I flew the trench in an o-200 powered Taylorcraft with only 24 gallons, 4:45 and I had 3 gallons left...at Watson Lake, weather was perfect or I would not have made it.
  10. I am lazy, I did 2.5" for the whole wing, it was...

    I am lazy, I did 2.5" for the whole wing, it was just easier to figure out for me.
  11. Replies
    19
    Views
    1,617

    Do you have curved and flat options? Templates?

    Do you have curved and flat options? Templates?
  12. Replies
    19
    Views
    1,617

    Pics would be nice for the new metal ones!

    Pics would be nice for the new metal ones!
  13. Are we allowed to do that here?

    Are we allowed to do that here?
  14. You guys are doing this the hard way, just...

    You guys are doing this the hard way, just install heated seat covers...:lol:
    https://www.amazon.com/Dorman-641-106-Dorman641-106-Seat-Heater/dp/B001KQD7LC Plug into a power connection, you can get...
  15. Replies
    13
    Views
    1,563

    Who did your overhaul at 2400?

    Who did your overhaul at 2400?
  16. Replies
    13
    Views
    1,563

    Here are a few rotax pics, I seem to repair a lot...

    Here are a few rotax pics, I seem to repair a lot of mid time jugs, that run 100LL. the oil on the jug came from a cracked copper washer under the bolt for the torque check on the gearbox. The entire...
  17. Replies
    13
    Views
    1,563

    I have 35 LSA 912's and 4 certified at my day...

    I have 35 LSA 912's and 4 certified at my day job...maybe we should start a Things to know about Rotax 912's thread? Still doesn't fix owner attitudes, this guy will basically have a like new...
  18. Replies
    13
    Views
    1,563

    But it was that way when I bought it...

    It is getting frustrating when owners/operators tell me that. I am trying to annual their airplane and the fiberglass landing gear is cracked...both landing gear and then the owners says he has been...
  19. Thread: Super cub plans

    by astjp2
    Replies
    7
    Views
    1,494

    Design by computer, cut with bandsaw, weld with...

    Design by computer, cut with bandsaw, weld with torch, fly by the seat of your pants...
  20. Replies
    29
    Views
    12,977

    337 with the wording “previously installed by...

    337 with the wording “previously installed by unknown persons” will go a long ways towards an approval.
  21. Replies
    29
    Views
    12,977

    There are some parts manuals that are now...

    There are some parts manuals that are now approved, but it’s not the normal.
  22. Replies
    76
    Views
    25,168

    this has been great reading, I do think that a...

    this has been great reading, I do think that a lot of information on here shows the experience that may have. Which leads me to a couple of questions about a certified installation, doesn't the...
  23. Replies
    32
    Views
    6,642

    I just tried to view the Ogden airport Facebook...

    I just tried to view the Ogden airport Facebook page, got a weird error, maybe I am banned and donít know it? Lol
  24. Replies
    74
    Views
    12,076

    we have 13 injected Lycomings and one carb one....

    we have 13 injected Lycomings and one carb one. Students suck at starting, constantly flood starting and half throttle…
  25. Replies
    31
    Views
    24,090

    Sticky: This is not how you should install a tanis along...

    This is not how you should install a tanis along with an ok way
Results 1 to 25 of 373
Page 1 of 15 1 2 3 4