Search:

Type: Posts; User: DENNY

Page 1 of 20 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    7
    Views
    561

    That is GPS speed. I was doing some ground...

    That is GPS speed. I was doing some ground effect training on day and got GPS speed down to 34, I was real happy with myself until I turned around and realized the wind picked up and I had 3 on the...
  2. Replies
    32
    Views
    1,053

    My tug is an old ATV! DENNY

    My tug is an old ATV!
    DENNY
  3. Replies
    32
    Views
    1,053

    Change the stop point on the door opener. DENNY

    Change the stop point on the door opener.
    DENNY
  4. Replies
    7
    Views
    561

    Stock wing with VG’s Full flap power on 1800 rpm...

    Stock wing with VG’s Full flap power on 1800 rpm I can slow to 37 mph but tail wheel is well below the mains. I would say normal touchdown speed after flair to slow and release back pressure to get...
  5. Replies
    20
    Views
    761

    Just trade/sell your 1 1/2 stuff and get new/used...

    Just trade/sell your 1 1/2 stuff and get new/used 1 1/4 rims disks to go on the Dodge gear. You will be money ahead in the long run. I have seen a lot of mixed sets that the owner tried to get by...
  6. Thread: Scott/abi 3200

    by DENNY
    Replies
    7
    Views
    379

    WTB: Almost looks like the spring is small for the...

    Almost looks like the spring is small for the head.
    DENNY
  7. Replies
    37
    Views
    1,838

    Soooooo when we are talking wing tips are we...

    Soooooo when we are talking wing tips are we including the last two rib bays (round tip wing), or are we just talking about two full bays normal rib profile with a tip on the end, or the STC that...
  8. Replies
    32
    Views
    1,383

    I was 50 years old when I started to fly. I...

    I was 50 years old when I started to fly. I found and paid for a 1956 pa22/20 before I took did any training. I took that airplane all over ALASKA!! I think it is the best trainer anyone could...
  9. Replies
    31
    Views
    1,249

    I would say the major problem is people are...

    I would say the major problem is people are trying to get by with 60 year old airframes and seats without good inspections at rebuild or along the life of the aircraft!! At some point in the life of...
  10. Replies
    34
    Views
    2,586

    I love the Cabela's mod!! However that seat back...

    I love the Cabela's mod!! However that seat back will be a major pain for anyone getting in and out of the back when you fold it down. Do a search, lots of better ways to fold the seat back without...
  11. Replies
    7
    Views
    368

    Jerry They both have the same amount of...

    Jerry
    They both have the same amount of problems. It is just without a 4 cylinder EGT/CHT you have to wait until issue has caused enough damage that you notice it. Burning a valve from an...
  12. Replies
    52
    Views
    5,206

    I see one of your problems. You think the Bogart...

    I see one of your problems. You think the Bogart p-lead "come with the P-lead shielded wire and a ground wire for each mag". It is a single shielded wire. The ground is the shield wire. They...
  13. Replies
    7
    Views
    368

    On a hard climb my #2 is the hottest, the reason...

    On a hard climb my #2 is the hottest, the reason I know this is I have a 4 cylinder EGT/CHT. Without that you don't know what you don't know! A single probe is about as useful at tits on a boar...
  14. Replies
    52
    Views
    5,206

    The mag "ground screw" is just a connection to...

    The mag "ground screw" is just a connection to the mag case, grounding to the engine which has continuity to the mag case has the same effect (as long as electrons have a path to follow). In planes...
  15. Thread: Oil temp

    by DENNY
    Replies
    16
    Views
    1,051

    Check the mag timing before you get too far down...

    Check the mag timing before you get too far down the path.
    DENNY
  16. Replies
    14
    Views
    920

    Depending on your tailwheel time and mission you...

    Depending on your tailwheel time and mission you may have an opportunity to replace fabric and sooner than you would like:oops:. I would agree with the others buy it and fly it.
    DENNY
  17. Replies
    82
    Views
    23,413

    Did you check with Airframes Alaska, Stoddards in...

    Did you check with Airframes Alaska, Stoddards in Anchorage, or Javron.
    DENNY
  18. Replies
    7
    Views
    755

    Jay has a lowered mount 2 inches I believe,...

    Jay has a lowered mount 2 inches I believe, however you can not run standard mags with it.
    DENNY
  19. Replies
    0
    Views
    484

    Skwentna Roadhouse fly-in 6/6/2020

    Hi Everyone
    Cindy asked me to post an update on the Skwentna fly-in this weekend. The goal is to keep this a FUN AND SAFE event!!! With that in mind, plane parking is aways an issue due to...
  20. Thread: Safety cables

    by DENNY
    Replies
    4
    Views
    341

    WTB: If any cub needs safety cables it is stock...

    If any cub needs safety cables it is stock standard gear!!! That is why it was made. The new gear is much better, BUT it depends on how you fly/land. Has you passenger ever had the headset come...
  21. Replies
    36
    Views
    2,097

    What kind of mags? Pictures of baffling/cowling...

    What kind of mags? Pictures of baffling/cowling top, bottom. front, sides. What are the temps on all cylinders?
    DENNY
  22. Replies
    46
    Views
    2,896

    Buying a new fuselage has several advantages. If...

    Buying a new fuselage has several advantages. If you do I would not have it painted or power coated until you fit the interior and rig the tail and wings. I don't think I have ever seen a new...
  23. Replies
    26
    Views
    1,473

    I agree get a true Private Pilots license!! If...

    I agree get a true Private Pilots license!! If you are going to be doing cross country flights the extra training will be useful. Most any experimental will cost you 2-3 times more than a flying...
  24. Replies
    46
    Views
    2,896

    I would agree with mike, Do it in stages. At...

    I would agree with mike, Do it in stages. At least do not strip touch the wings until the fuselage and engine are done. You can hopefully get it done by May, fly the summer and then do the wings,...
  25. Replies
    7
    Views
    531

    Having an engine that can run mogas can save you...

    Having an engine that can run mogas can save you the price of a rebuild over the life of the engine. Having fuel flexibility on long or remote trips is also very handy. When you want dependable...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4