Search:

Type: Posts; User: Steve Pierce

Page 1 of 20 1 2 3 4

Search: Search took 2.24 seconds; generated 45 minute(s) ago.

  1. I'd say X Cub since the NX Cub is not yet...

    I'd say X Cub since the NX Cub is not yet certified.
  2. Replies
    243
    Views
    53,244

    I don't see where a spacer would be an issue,...

    I don't see where a spacer would be an issue, bolts to the flange like any other prop, just need longer mount bolts.
  3. Thread: Carb Ice

    by Steve Pierce
    Replies
    28
    Views
    1,674

    I torque the bowl screws, let it sit overnight...

    I torque the bowl screws, let it sit overnight and torque again the next day. Also the same as posted above on pre-flight. Seen the bowl loose several times.
  4. Interesting that I cannot find this service...

    Interesting that I cannot find this service bulletin anywhere but here. Not on Piper's website. Where did you get it?
  5. Replies
    14
    Views
    689

    We adapt and overcome. Have gotten my in-laws to...

    We adapt and overcome. Have gotten my in-laws to transport many wrecks and most recently a set of floats to the east coast. U Haul one way saved some money in gas.
    63842
  6. https://www.supercub.org/forum/showthread.php?6047...

    https://www.supercub.org/forum/showthread.php?60471-Rudder-Failure-NTSB-Notice-2252

    Somewhere is a thread on this. Saw one of the rudders at Oshkosh in the NTSB booth. I believe all the failures...
  7. Replies
    245
    Views
    116,826

    Being proactive I guess, every little bit helps.

    Being proactive I guess, every little bit helps.
  8. Replies
    59
    Views
    12,164

    Yep, you hold your mouth the same, say the same...

    Yep, you hold your mouth the same, say the same prayer and use the same words when the prayers don't work. ;)
  9. Replies
    59
    Views
    12,164

    Small flush cutting dikes on the back side to...

    Small flush cutting dikes on the back side to keep the rivet from spinning.
  10. Replies
    59
    Views
    12,164

    Is it a Piper rib or a Univair rib? Pictures?

    Is it a Piper rib or a Univair rib? Pictures?
  11. Replies
    245
    Views
    116,826

    Hopefully it would drain out the drain holes and...

    Hopefully it would drain out the drain holes and evaporate but who knows.
  12. Replies
    245
    Views
    116,826

    Yea, that was my understanding, if the fuel got...

    Yea, that was my understanding, if the fuel got on the back side of the fabric. I remember when Jason Gerard was working for Stewarts and doing the seminars here he would Ekofil and paint inside the...
  13. Replies
    99
    Views
    16,646

    Main issue I could see would be with the Bonanza...

    Main issue I could see would be with the Bonanza where the trim can over power the elevator. I know a guy who did not set the trim on a Bonanza correctly for take off and dam near killed him. My wife...
  14. Replies
    245
    Views
    116,826

    So if you spill paint on the tops of the wings it...

    So if you spill paint on the tops of the wings it softens the paint?
  15. Replies
    245
    Views
    116,826

    I don't see how spilling the top coat on the...

    I don't see how spilling the top coat on the catalyzed polyurethane is cause a problem. It is like any catalyzed paint only it is carried via water vs solvents. Can you post some pictures?
  16. Replies
    99
    Views
    16,646

    Yea, Have a few friends with the Garmin stuff in...

    Yea, Have a few friends with the Garmin stuff in a 182 and a Bonanza. I bet there are some Garmin software engineers working overtime. Engaging the autopilot at 2-300 feet in a Bonanza and getting a...
  17. Replies
    245
    Views
    116,826

    The issue is the backside of the fabric not the...

    The issue is the backside of the fabric not the top coat. Stewart System top coat is catalyzed polyurethane
  18. I renew online and it arrives very timely every...

    I renew online and it arrives very timely every time, 8 different airplanes. The one that took time was when I bought the new Super Cub, that took about 7 months.
  19. Replies
    68
    Views
    9,842

    Factory metal belly didn't cover under the...

    Factory metal belly didn't cover under the cockpit, that was still fabric. Factory panels weighed 9 lbs 10 oz.
  20. Replies
    3
    Views
    428

    Maggie Aircraft Ignition Harnesses

    One of the members on ShortWingPipers.org posted about Maggie Aircraft Harnesses so I went down a rabbit hole at lunch today and read everything on the website and watched all their videos. I am...
  21. Replies
    1,605
    Views
    564,806

    Sticky: Pulled my airplane out the other day to put two...

    Pulled my airplane out the other day to put two customer's airplanes in behind it. After work I was about to pull it back in as I looked at the windsock and decided I just needed to go fly. My middle...
  22. Replies
    99
    Views
    16,646

    What about Notice Number NOTC2741 on the Garmin...

    What about Notice Number NOTC2741 on the Garmin GFC 500 telling certified users to pull the breaker until Garmin comes up a with a fix.




    Garmin GFC 500 Autopilot Notice
    Notice Number:...
  23. Replies
    9
    Views
    826

    I have wrapped a piece of silicone baffle...

    I have wrapped a piece of silicone baffle material around SCAT tube before but wasn't in direct coct with the exhaust. Might need a little experimentation.
  24. Replies
    6
    Views
    1,131

    The Bat Pacer, built by Charlie Center at...

    The Bat Pacer, built by Charlie Center at Crosswind STOL if memory serves me correctly or has all of his mods at least. Interesting airplane when I saw it and met the previous owner at Birchwood...
  25. Correct. Also, the seat has no relevance on...

    Correct. Also, the seat has no relevance on adjustable on non-adjustable cap. The old caged style relief valve seat uses a larger diameter oil pressure relief valve housing where the machined seat...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4