Search:

Type: Posts; User: Steve Pierce

Page 1 of 20 1 2 3 4

Search: Search took 2.31 seconds.

  1. Replies
    22
    Views
    835

    From what I know, yes. I would not remove the...

    From what I know, yes. I would not remove the header tanks unless I welded in the front right fuel line and change the front left one to 3/8" from 1/4". There is a reason the STCs require these...
  2. As stated above, installing mechanic determines...

    As stated above, installing mechanic determines compatibility of STCs. I wouldn't have an issue with it. Look at the engine type certificate data sheet for the difference between your engine and the...
  3. Replies
    24
    Views
    1,646

    I have a set for sale.

    I have a set for sale.
  4. Replies
    9
    Views
    1,011

    Dang, I wasn't suppose to post that picture of my...

    Dang, I wasn't suppose to post that picture of my new weight saving trick. 8)
  5. Replies
    22
    Views
    835

    You don't have to buy their tanks, just the fuel...

    You don't have to buy their tanks, just the fuel valve and gascolator.
  6. Replies
    9
    Views
    1,011

    There is a radius milled in the block of the rear...

    There is a radius milled in the block of the rear strut where it changes angles. Problem is on the 4 airplanes I have gotten feedback and looked at personally that distance from the edge of the hole...
  7. Replies
    21
    Views
    1,057

    I have been getting stuff from Ft. Worth,...

    I have been getting stuff from Ft. Worth, Illinois and California but just one shipping charge but usually I get free shipping if over $250 on my dealer account.
  8. Replies
    9
    Views
    511

    I found that 1/2" toe in on 31" Dessers was a...

    I found that 1/2" toe in on 31" Dessers was a bear. How did the plane react prior to the gear swap? When I repair fuselages we weld the gear fittings on with them parallel.
  9. Replies
    21
    Views
    1,057

    Did the parts come from the US or Aircraft Spruce...

    Did the parts come from the US or Aircraft Spruce Canada? I know my shipping costs to Canada are crazy. I have been getting lots of split shipments from Spruce lately from their different locations....
  10. Replies
    15
    Views
    567

    Original 1982 Piper master solenoid. Slightly...

    Original 1982 Piper master solenoid. Slightly modified battery shelf and battery install.
    55505
  11. Thread: Arkansas

    by Steve Pierce
    Replies
    6
    Views
    477

    Byrd's Adventure Center is great. Richland Creek...

    Byrd's Adventure Center is great. Richland Creek and Trigger Gap are great camping spots as well. Lots of amazing scenery.
  12. Replies
    9
    Views
    1,011

    I waiting on Airframes.

    I waiting on Airframes.
  13. Replies
    9
    Views
    1,011

    Airframes Aluminum Strut Issue

    Installed my first set of Airframes aluminum struts today and discovered an issue with the rear strut. Where the front of the strut attach block meets the wing strut attach fittings the joggle that...
  14. Replies
    7
    Views
    546

    I like this one. One of my helpers exceeded it's...

    I like this one. One of my helpers exceeded it's design limits and they sent me new bushing and special shouldered screws for free.
    ...
  15. Replies
    26
    Views
    2,946

    The guys that tested the props in Alaska told me...

    The guys that tested the props in Alaska told me they had higher CHTs with the Sensenich.
  16. Replies
    7
    Views
    546

    Easy Way to Cut Open an Oil Filter

    I always hated cutting open oil filters for inspection. Even had to make a trip to the emergency room for stitches once. My friend Jon Delamarter showed me this handy trick that makes it pretty easy....
  17. Replies
    21
    Views
    1,057

    Have you called them. I have Jim Irwin's personal...

    Have you called them. I have Jim Irwin's personal email address and if I don't get anywhere with his employees I contact him. He has helped all 3 times I have contacted him.

    Sold a Bungee Buddy...
  18. Replies
    3
    Views
    302

    The stabs should float on the front liner tube....

    The stabs should float on the front liner tube. The liner tube is not attached to the carry-thru tube that is bolted to the jackscrew yoke.
  19. Replies
    3
    Views
    302

    Replace the liner tube and pull the stabs up...

    Replace the liner tube and pull the stabs up tight when you drill it for the 3/16" bolts.
  20. Replies
    10
    Views
    593

    I guess in the grand scheme of things I don't see...

    I guess in the grand scheme of things I don't see the paint being that expensive. I guess I have seen the issues when I tried to fix paint when someone touched up bad spots with spray paint, enamel...
  21. Replies
    18
    Views
    679

    Kevin, I have pondered the same question and...

    Kevin, I have pondered the same question and don't believe it matters if the up cable is on the left pulley or the right.
  22. Replies
    10
    Views
    593

    I just touched up a hangar rash yesterday on a...

    I just touched up a hangar rash yesterday on a Super Cub I rebuilt a little over a year ago. Luckily I have paint, catalyst and reducer. I use these. ...
  23. Replies
    6
    Views
    1,147

    Wish I was close Troy, be good to catch up.

    Wish I was close Troy, be good to catch up.
  24. Replies
    9
    Views
    525

    I know someone who did the same thing in an Ag...

    I know someone who did the same thing in an Ag Cat after doing some light aerobatics. Old timer told him they always carried a long screw driver to be sure the parking brake tabs were down.
  25. Replies
    264
    Views
    39,293

    A bubble level and a string worked for me for...

    A bubble level and a string worked for me for years. However I find it easier, quicker and have better results with a digital level. Dihedral is very subjective because of the way they skins lay on...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4