Search:

Type: Posts; User: Glidertow

Page 1 of 5 1 2 3 4

Search: Search took 0.01 seconds.

  1. Thread: Dihedryl

    by Glidertow
    Replies
    12
    Views
    4,827

    Well it is your money, but I bet you trust an app...

    Well it is your money, but I bet you trust an app to run your GPS, file your flight plan, show you the weather, order your parts, tell you the temp, humidity, and due point. They all run off the...
  2. Thread: Dihedryl

    by Glidertow
    Replies
    12
    Views
    4,827

    Digital level ? There is an app for that! Check...

    Digital level ? There is an app for that! Check out carpenter tools app. Then just get a straight piece of metal or wood about 30" long and you just saved $160
  3. Replies
    136
    Views
    43,754

    Steve, in your picture above, the spring is lying...

    Steve, in your picture above, the spring is lying on the elevator turnbuckle. This is what mine is doing. I was just concerned it would either hang up or cause wear.
  4. Replies
    136
    Views
    43,754

    Yes, pulled back.

    Yes, pulled back.
  5. Replies
    136
    Views
    43,754

    Thanks everybody for your answers, an interesting...

    Thanks everybody for your answers, an interesting subject that appears to be unresolved. Im like the little baby in the insurance commercial "Does it bother anybody" that the spring and cable goes...
  6. Replies
    136
    Views
    43,754

    Do you have a picture showing futher back. What...

    Do you have a picture showing futher back. What position should it be at neutral elevator trim? How does one know the measurement of the complete cable and spring.
  7. Replies
    136
    Views
    43,754

    I have installed the upper cable as shown on the...

    I have installed the upper cable as shown on the above flie drawing. When the elevator is raised the spring goes limp and looks as though there could be a possible control cable interference with...
  8. Replies
    45
    Views
    14,798

    Darrel, I'm using the B and C starter. I have...

    Darrel, I'm using the B and C starter. I have gotten myself confused reading the post on various part numbers for the solenoids. BC offers some. What did use use?
  9. Replies
    15
    Views
    6,979

    Any update on this thread? Source for bushings?

    Any update on this thread? Source for bushings?
  10. Replies
    7
    Views
    2,417

    My real question has to do with the spring being...

    My real question has to do with the spring being so slack that it lays down on the elevator cable when full back. Just does not seem safe.
  11. Replies
    7
    Views
    2,417

    Also seeking help with question 4 above.

    Also seeking help with question 4 above.
  12. Replies
    32
    Views
    12,547

    This happens when in neutral position. Surely...

    This happens when in neutral position. Surely this is unsafe for both cables to touch and have possible interference.
  13. Replies
    32
    Views
    12,547

    I must have something really wrong on my build....

    I must have something really wrong on my build. Stock Univair parts...when I pull up elevator the cable a spring are slack and if fact lay on top of the elevator turnbuckle. What's up?
  14. Replies
    35
    Views
    9,536

    Thanks for the replies. Dakota's are 67.00 each....

    Thanks for the replies. Dakota's are 67.00 each. On the original drawings what is the bushing and what holds in in place. Is it like a cable sewage?
  15. Replies
    35
    Views
    9,536

    Brake tie rod

    I have the standard brakes and heel/brake pedals on my PA-18 project. What is the best way to make the tie rod between the two?
  16. Replies
    5
    Views
    3,090

    Valve cover Clearence

    After installing millenium cyl with their valve covers and making my own cowl doors I find a very small Clearence on the right rear cal and the door. Maybe only a 1/1000 inch.. Do not want to put a...
  17. Replies
    11
    Views
    6,794

    Please share your method of getting the baffle to...

    Please share your method of getting the baffle to fold properly as you pointed out above.
  18. Replies
    5
    Views
    2,608

    Thank you, that is just what I needed to see.

    Thank you, that is just what I needed to see.
  19. Replies
    5
    Views
    2,608

    Alternator Off light

    I have a B&C alternator, 0-320 and would like to put a light on the panel to warn if the alt has dropped off line. How is such a light wired in?
  20. Replies
    12
    Views
    4,632

    Try OnLineMetals.com. They have been great to...

    Try OnLineMetals.com. They have been great to deal with.
  21. Thread: Cowl doors

    by Glidertow
    Replies
    17
    Views
    8,528

    Thanks Mike, perfect timing, I just fit the...

    Thanks Mike, perfect timing, I just fit the clasps this weekend and I am now ready to mark for triming.
  22. Thread: Cowl doors

    by Glidertow
    Replies
    17
    Views
    8,528

    Cowl door

    Well Mike I have not roll it. I have a small combo brake/roller but frankly i have never gained enough experience to use it. The doors i took off had the steel bend piece in the back edge and were...
  23. Thread: Cowl doors

    by Glidertow
    Replies
    17
    Views
    8,528

    Cowl doors

    I am in the process of building new cowl doors for my project, PA-18-150. I have the new nose bowl installed, I have clecoed the hinge and the rear bow to form the curve. My question is what is the...
  24. Replies
    34
    Views
    13,090

    Darrel, you may be getting ripped. Google...

    Darrel, you may be getting ripped. Google Fleetfilter, a NAPA on line store, still $9.95.
  25. Replies
    34
    Views
    13,090

    I have not picked it up yet, but my local NAPA...

    I have not picked it up yet, but my local NAPA store has them for $9.95.
Results 1 to 25 of 108
Page 1 of 5 1 2 3 4