Search:

Interesting. I didn’t think US citizens could enter Canada yet?

And apparently US pilots can fly for hire in Canada? Many years ago I had a job in Alberta and was asked for my work permit by an...

Mike, we get both. I don’t know where they’re from but Fairchild is likely.

This afternoon my wife and I were out at our cabin when I heard one go right over us. I went outside and looked...

The Kid and I have a legitimate complaint with these C130s. They come through our narrow river valley at low level and don’t monitor the CTAF or make any position reports. In October I was in the...

This is a lightly used set of wing and tail feather covers. Five pieces total. I got these from a friend when he sold his C-182 and they fit my C-172 just fine. But I'm hangared and have never...

My in-laws had this little Coleman stove in their garage and it ended up here from their estate. I cleaned it up and was curious about it not having seen these smaller propane canisters. I wondered...

I bought a 52” Grizzly about 10 years ago and I and another builder have used it quite a bit. It has held up well to our light duty uses with aluminum and kydex. And shorter pieces of steel are fine...

Looking excellent Bob. Won’t be long and your Monster will be ready for anything you ask of it.

Excellent Bill. Your combination of humility and experience is appreciated. I especially liked your class G flying tips.

Could you tell us a little more about your little outboard motor? I...

Original panel with backer.

52906

asking $100 plus shipping.

Please PM or respond to this thread.

These are original Piper interior panels. They would work well for using as patterns for making new panels from aluminum or Kydex for an experimental. Or maybe they’re better than what you’ve got...

Sold

This is Univair part number PA25TWS1-3L. New these are $183 from Univair. The weight is an even 5 pounds.

This was removed from my Experimental Cub when I replaced it with a T3.

I'd like...

https://iflyei.com/product/fp-5l-fuel-computer/


This EI fuel flow gauge is supposed to show HP%. I have the earlier version in my Cessna, before the HP calculation was added, and it is an...

I’d say that’ll give you all the movement you might need. It doesn’t take much but rigid isn’t good IMO.

52599

here’s the form I made about ten years ago. You guys have inspired me to pick up...

Farm boy, I like your tail ski. Is that made from black UHMW? How thick? I once made a wooden form to shape a similar ski around but never finished the project. I like your simple approach too.

I’ve got a Pawnee spring I took off when I put the T3 on my Cub. If you want to try it PM me and I’ll send it to you.

My answer would be no, I do not change trim in the pattern. I also don’t close the throttle until I am stopped. I dial in nose-down trim and leave it there. I like the feel of pulling back on the...

I'd be a little concerned with it being unable to flex with changing snow contours.

52552

There is a Burl's ski under this snow. This tail ski has a piston with springs on either side that...

Yes I have done my last three Flight Reviews with them. Two were in their PA18 on straight floats and the last one, in July of this year, in my plane. I would rate them as good all around. I’ve only...

52057

I landed on a bar on the Clark Fork in my old PA18 in 2009 that was almost too short. Some friends that came by in a jet boat took the picture.

Bill, I thought about your Cub. Maybe...

This is an all-custom rifle. The action is a Defiance Machine, stock is a McMillan and the barrel is custom too. The scope is a Nightforce.

I've seen a lot of elk killed from the .243 to the...

The GDL 50 series In’s will Bluetooth to your 796 and show everything that’s available. That’s what I use.

The barrel is 22”. It is a nice lightweight rifle at 7.25 pounds. The 210s leave at 2600 FPS and hit hard. I’ve killed two elk and three bucks with this rifle now and am impressed.

That was a close one!

This must be on the short section of the river in Idaho? I can’t think of a section of river in Montana on the Lower Clark Fork where there is both a hydroelectric dam and...

Yes a Texas Hunting club bought a big chunk of scattered sections on the south side of the Clark Fork here too. Probably the same group. But I think most of the Thompson River ground got put into a...