Search:

Type: Posts; User: mike mcs repair

Page 1 of 20 1 2 3 4

Search: Search took 0.09 seconds.

  1. Thread: Draco

    by mike mcs repair
    Replies
    2
    Views
    165

    Oops, darn it... ...

  2. Replies
    1,249
    Views
    320,658

    I bet he's already looking for a donor.... ...

    I bet he's already looking for a donor....

    plenty of good parts left....
  3. Replies
    1,249
    Views
    320,658

    https://www.youtube.com/watch?v=NfctWAoDXvs

    https://www.youtube.com/watch?v=NfctWAoDXvs
  4. Replies
    1,249
    Views
    320,658

    https://www.youtube.com/watch?v=TtDL3jv4gEQ

    https://www.youtube.com/watch?v=TtDL3jv4gEQ
  5. Replies
    2
    Views
    73

    PA 12 wheel gear wanted

    Does it still have normal-12 gear setup or has it been converted to -18 gear(you can tell if it has cabane V mounting ears added to front gear fittings)


    Sent from my iPhone using SuperCub.Org
  6. Replies
    3
    Views
    183

    Won’t show on normal compression check. Rings are...

    Won’t show on normal compression check. Rings are above crack. The various ADs have yo do a soppy water check with piston BDC if I recall correctly. Thanks for sharing


    Sent from my iPhone...
  7. the bushing are on my inspection sheet as an...

    the bushing are on my inspection sheet as an item, you will wear the bottom ones out first & quite quickly...
  8. Replies
    51
    Views
    7,656

    and that's why I only use vinyl for NNumbers (and...

    and that's why I only use vinyl for NNumbers (and I've had a few on different airplanes that I had to replace after only a few years...)

    the failure mode is they curl up from the edges... I will...
  9. this is also the only way I have seen it done.......

    this is also the only way I have seen it done.... never seen that one bolt into the truss.....
  10. Replies
    3
    Views
    252

    Pictures. No 2 -12 are the same Sent from...

    Pictures. No 2 -12 are the same


    Sent from my iPhone using SuperCub.Org
  11. bump.... any more thoughts on this issue... or is...

    bump.... any more thoughts on this issue... or is it a dead/bad idea?
  12. Replies
    15
    Views
    360

    atlee has new tooling now, no more fluted edges ...

    atlee has new tooling now, no more fluted edges nice and smooth lips
  13. Replies
    15
    Views
    360

    http://www.fadodge.com is where I get my...

    http://www.fadodge.com is where I get my firewalls... he will make them out of stainless or titanium they have a nice lip formed on them

    https://photos.app.goo.gl/oiBAbRz69vR1eM4i9
    ...
  14. Replies
    131
    Views
    27,856

    Start fan on high an hour before painting, the...

    Start fan on high an hour before painting, the turn fan down during painting(moves dust before you paint). Fast fan should have moved the dust. Also hang parts vertically or top DOWN(good side)

    ...
  15. Replies
    10
    Views
    488

    Cessna Pilots Seat.

    http://everyspec.com/MIL-STD/MIL-STD-1700-1799/download.php?spec=MIL-STD-1755.020900.PDF


    Sent from my iPhone using SuperCub.Org mobile app
  16. https://goo.gl/photos/PuiR5ha2aBDbkUBS8 ...

    https://goo.gl/photos/PuiR5ha2aBDbkUBS8

    https://goo.gl/photos/GRXyyNHPoUik2V44A

    You may need to move throttle handle some. And mod rod between handles


    Sent from my iPhone using SuperCub.Org
  17. Replies
    3
    Views
    398

    your plane is an OLD CAR 3 or CAR 03 certified...

    your plane is an OLD CAR 3 or CAR 03 certified plane...

    search for it... should meet the tire requirements... it was very broad
  18. Replies
    1,249
    Views
    320,658

    sure don't see much fuel spilled there..... or...

    sure don't see much fuel spilled there..... or fire.....
  19. Replies
    1,249
    Views
    320,658

    2 times a few summers ago, i watch 2 planes...

    2 times a few summers ago, i watch 2 planes engines quit after/on takeoff, one successfully got it going again.... other was fatal as he tried to turn back and stalled.... I walk by that spot where...
  20. Replies
    93
    Views
    11,416

    I've seen noise/fixed from: loose screw on...

    I've seen noise/fixed from:

    loose screw on output breaker(would sometimes weld, other time be loose and noisy)
    bad grond alt to airframe
    bad master solenoid, burnt contractor?


    (not sure...
  21. Replies
    1,249
    Views
    320,658

    https://www.youtube.com/watch?v=Ljz079fzu7o

    https://www.youtube.com/watch?v=Ljz079fzu7o
  22. Replies
    62
    Views
    20,912

    It was an OLD ABANDONED STC. Had to do it by...

    It was an OLD ABANDONED STC. Had to do it by field approval using that as data. That was 2 decades ago. Or so was the one I did.


    Sent from my iPhone using SuperCub.Org mobile app
  23. Replies
    27
    Views
    1,438

    Watched it last night also.... should be...

    Watched it last night also.... should be interesting.


    Sent from my iPhone using SuperCub.Org
  24. Replies
    85
    Views
    27,399

    you NEED TO ADD more shims under your bearing if...

    you NEED TO ADD more shims under your bearing if tightening the nut stops swiveling on a cessna style scott
  25. but what if fuselage is in one pile, and wings...

    but what if fuselage is in one pile, and wings are in another? and you are just putting it back together enough to get it home??

    that's what a ferry permit is for in my world.... not just for out...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4