Search:

Type: Posts; User: kevinbarton1

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    13
    Views
    813

    FS: Also, it does not seem as though your flap handle...

    Also, it does not seem as though your flap handle connects to your seat. I have a lug welded to the seat with a modification that extended the log out a couple of inches to receive the flap handle...
  2. Replies
    13
    Views
    813

    FS: Tango Cub Flap cable attaachment

    Thanks for the reply. I cannot see the flap cable attach point to the handle base so I assume the attach point is on the inside of the interior panel. Maybe someone has a shot from the other side or...
  3. Replies
    13
    Views
    813

    FS: Also, we are having an issue with our cables...

    Also, we are having an issue with our cables rubbing where the horizontal stabilizer trim cables pass each other from the larger metal pulley to the smaller.

    42638


    Sent from my iPhone using...
  4. Replies
    13
    Views
    813

    FS: If we place the flap handle in the forward lug,...

    If we place the flap handle in the forward lug, it seems the flap cable attaches on the inside of the interior panels. That would be ok, but it doesnít seem obvious where the cable would run through...
  5. Replies
    13
    Views
    813

    FS: Tango Cub flap handle attachment

    As we were putting our new seat base and looking to install the flap handle, we noticed the old flap handle attachment lug was considerably further forward on the fuselage than a regular PA-18. We...
  6. Replies
    26
    Views
    4,420

    I can only imagine it is probably a dream. I...

    I can only imagine it is probably a dream. I would love to put one on now, but the cost of the rebuild is getting more costly by the week. I will definitely consider at some point in the future. I...
  7. Replies
    43
    Views
    7,318

    I just have the stock tie down rings that bolt on...

    I just have the stock tie down rings that bolt on the upper part of the strut. I have never seen the Hurricane tie downs. Frankly hope I never need any!!!
  8. Replies
    43
    Views
    7,318

    I know, I did not think I would ever put a...

    I know, I did not think I would ever put a transponder in it, but the more I think about it, the more I will likely put one in. Sooner than later I am sure.
  9. Replies
    43
    Views
    7,318

    Progress

    We are making some progress now that we have the frame back from the weld shop. Fitting the 3 piece cowling, flight controls, fuel system, pulleys and will hopefully start on the electrical this...
  10. Replies
    43
    Views
    7,318

    I will check on the fly wheel tooth count.

    I will check on the fly wheel tooth count.
  11. Replies
    43
    Views
    7,318

    I was planning to use the rear mounted oil...

    I was planning to use the rear mounted oil cooler. A guy at Sutton Exhaust gave me this: NDM oil Coolers part # 08-00741

    I will call and get a new stabilizer carry through.

    As always, thanks...
  12. Replies
    43
    Views
    7,318

    40347 We noticed that the parts manual shows a...

    40347

    We noticed that the parts manual shows a grease fitting on this part, but my 1953 original doesnít have one. I prob can guess the answer, but should I replace with a newer style that has the...
  13. Replies
    43
    Views
    7,318

    No worries, Iíll order from Atlee!! Thanks for...

    No worries, Iíll order from Atlee!! Thanks for the reply...


    Sent from my iPhone using SuperCub.Org
  14. Replies
    21
    Views
    1,986

    [emoji12] Sent from my iPhone using...

    [emoji12]



    Sent from my iPhone using SuperCub.Org
  15. Replies
    43
    Views
    7,318

    I knew there had to be an easy way to lift the...

    I knew there had to be an easy way to lift the plane! Thanks for your knowledge and reply Steve! My prop was delivered today. Progress every day.
  16. Replies
    43
    Views
    7,318

    I'll take them! Looks easy enough to install. You...

    I'll take them! Looks easy enough to install. You can PM me and I will send you a check. Thanks for the post! Kevin
  17. Replies
    21
    Views
    1,986

    Yes, a few times. It is tight along the north...

    Yes, a few times. It is tight along the north edge of the runway. The fence line is very close to the runway edge. More of a mind game than anything the first time you land there. Big trees when you...
  18. Replies
    21
    Views
    1,986

    You can for sure. We do but there are some signs...

    You can for sure. We do but there are some signs toward the edge of the taxi way/ramp you would want to avoid. They arenít directly in the way, but donít get off the center.


    Sent from my iPhone...
  19. Replies
    21
    Views
    1,986

    I have a large hangar at Kestrel Airpark. We are...

    I have a large hangar at Kestrel Airpark. We are just about 20 miles East of Boerne off Hwy 46 and Hwy 281. Would be happy to accommodate you for a few nights. We are normally pretty full, but we...
  20. Replies
    17
    Views
    4,630

    Yesterday was a beautiful day! Sure looks fun! ...

    Yesterday was a beautiful day! Sure looks fun!


    Sent from my iPhone using SuperCub.Org
  21. Replies
    43
    Views
    7,318

    Thanks Jim. I have the float fittings, and lift...

    Thanks Jim. I have the float fittings, and lift handles on both sides of the tail. Iíll check into the tabs on the door opening. When I do put it on floats, how do most people ďliftĒ the aircraft to...
  22. Replies
    43
    Views
    7,318

    Iím very glad I asked!!! Thanks for that post....

    Iím very glad I asked!!! Thanks for that post. Will be fitting the boot cowl this week.


    Sent from my iPhone using SuperCub.Org mobile app
  23. Replies
    43
    Views
    7,318

    I can appreciate your sense of humor btw on...

    I can appreciate your sense of humor btw on friends not letting you use riv nuts. LOL. I wasnít aware of square nuts for the U Channel so I will check into that. I want to build the plane with the...
  24. Replies
    43
    Views
    7,318

    We definitely have the keyed riv nuts. We are by...

    We definitely have the keyed riv nuts. We are by no means professional builders, but I like to do things the right way. Is it possible to use nut plates on the U Channel??


    Sent from my iPhone...
  25. Replies
    43
    Views
    7,318

    We were going to use Riv Nuts in the U channel...

    We were going to use Riv Nuts in the U channel and nut plates anywhere else we can fit them. I wanted to stay away from using sheet metal screws.



    Sent from my iPhone using SuperCub.Org mobile...
Results 1 to 25 of 50
Page 1 of 2 1 2