Search:

Type: Posts; User: Mark_Moyle

Page 1 of 11 1 2 3 4

Search: Search took 0.02 seconds.

  1. Thread: tach seal

    by Mark_Moyle
    Replies
    4
    Views
    297

    Iíve used a close quarters right angle drill with...

    Iíve used a close quarters right angle drill with a short number 40 drill bit..drilled two holes into the seal, screwed in a couple number 6 sheet metal screws then slipped a short tiny torx head bit...
  2. TM Technologies sells dimpled shrinker and...

    TM Technologies sells dimpled shrinker and stretching dies for the Lancaster style to sneak up on the fit without leaving the sure to crack marks the standard dies create.


    Sent from my iPad...
  3. Replies
    83
    Views
    4,294

    Weld Quality

    Couple things. One 4130 if TIG welded...weld the entire cluster. TIG induces heat quickly. A hot fast bead may look pretty but itís not acceptable unless the cluster has been preheated. The...
  4. Replies
    31
    Views
    2,317

    Anyone have the 11 gallon Stoddardís drawings? I...

    Anyone have the 11 gallon Stoddardís drawings? I have the paper work....forwarded to Cub Crafters four years ago...did they do anything with it?


    Sent from my iPad using Tapatalk Pro
  5. [QUOTE=DENNY;785292]Go get some spin/aerobatic...

    [QUOTE=DENNY;785292]Go get some spin/aerobatic training next..
    Then come back and tell us if you screamed like a little girl when your instructor can get......say in a PA20....the airplane to spin...
  6. .028Ē. Is great for covering small areas that...

    .028Ē. Is great for covering small areas that donít need rigidity in the panel..https://uploads.tapatalk-cdn.com/20201016/86292c348e3cf8a58b0a905f5dbdc2fd.jpg


    Sent from my iPad using Tapatalk Pro
  7. Replies
    21
    Views
    3,750

    C-90 gets tight when warm

    Iíve seen this before...but none of the rigs had propellers. Carbon build up between the piston rings and the ring grooves was pretty common on old flat heads that ran rich...few fords and chevy...
  8. Thread: New PPONK

    by Mark_Moyle
    Replies
    120
    Views
    14,977

    Iím curious...has anyone used a permold engine...

    Iím curious...has anyone used a permold engine when doing the O-520 conversion? Youíd think the IO520BA with the flat back case, small journal VAR crank and front mounted alternator would be...
  9. Thought about that... since Iíve got drain...

    Thought about that... since Iíve got drain bramage at times I donít do it. The only time I pull on the prop is during pre-flight check.. I push and pull to see if the thrust bearing clearance has...
  10. Replies
    63
    Views
    4,390

    Eddie Trimmer May have the finished the STC for...

    Eddie Trimmer May have the finished the STC for Maule oleo struts for the 3Ē extended gear on a PA18...


    Sent from my iPad using Tapatalk Pro
  11. Replies
    39
    Views
    2,927

    Yup.. brought in back in 2008 to pour the...

    Yup.. brought in back in 2008 to pour the platinum concentrate recovery building. Then a Basket ball court, hanger floor and new powerhouse. Next is a hydronic heated slab for a new post office.
    ...
  12. Bought one of these recently....Wonder if this...

    Bought one of these recently....Wonder if this would work?

    https://www.aircraftspruce.com/catalog/topages/beadbuster.php?clickkey=52413


    Sent from my iPad using Tapatalk Pro
  13. Replies
    39
    Views
    2,927

    Walking beam suspension...tire squat wasnít a...

    Walking beam suspension...tire squat wasnít a factor...had about 3/4Ē clearance.


    Sent from my iPad using Tapatalk Pro
  14. Replies
    39
    Views
    2,927

    Just that close to making it in the hangar

    The Schweiss bi-fold, strap lift door can be opened manually by removing the brake cover on the motor. When we poured the slab in the hanger...the mixer truck didnít clear the door. I raised the...
  15. Replies
    37
    Views
    2,970

    I bought a 1950 Pacer with narrow gear....should...

    I bought a 1950 Pacer with narrow gear....should have listened to Eddie Trimmer when he recommended beefing up the landing gear... he may have found all the cracks during that upgrade.....209...
  16. Replies
    727
    Views
    352,844

    Sharing my version of a wing rotator using Honda...

    Sharing my version of a wing rotator using Honda ATV CV...
  17. Replies
    34
    Views
    2,943

    RICE....uncooked.....is a very very good carbon...

    RICE....uncooked.....is a very very good carbon deposit remover...
    Once upon a time I liked John Deere...bought a new common rail 65kW...the first two warrantee repairs cost Deere more than I paid...
  18. Okay...since Iím the guy that maintains...

    Okay...since Iím the guy that maintains PAPM...when do I get the $20k? Iíll make sure the runway is um...just like it is...perfect..did see one runway light out today...Iíll fix that!


    Sent from...
  19. Thread: Skidding 12

    by Mark_Moyle
    Replies
    26
    Views
    4,221

    Zero thrust line on the engine requires the...

    Zero thrust line on the engine requires the leading edge of the vertical stabilizer to be off set. The Bearhawk offset is 3/4Ē from centerline.


    Sent from my iPad using Tapatalk Pro
  20. Replies
    13
    Views
    1,323

    On every Diesel engine Iíve overhauled the...

    On every Diesel engine Iíve overhauled the exhaust manifold/s gets a good coat of engine...
  21. Thread: Hangar home

    by Mark_Moyle
    Replies
    57
    Views
    7,543

    I REALLY wish I had engineered in a underground...

    I REALLY wish I had engineered in a underground passway, a tunnel, between the two structures. On this mountain, anything outside creates drifts, and problems. A tunnel with the roof flush with the...
  22. Replies
    1,993
    Views
    492,966

    Isnít this the same outfit who put a Platus down,...

    Isnít this the same outfit who put a Platus down, gear up just, on a frozen lake.... after departing Koliganek a few weeks ago?


    Sent from my iPad using Tapatalk Pro
  23. Replies
    100
    Views
    11,264

    I was thinking...have a mashed in, face plate...

    I was thinking...have a mashed in, face plate busted transponder just sitín there...when asked what happened to your ADS-B unit?....answer....I did this thing..like went under this err...like a...
  24. Replies
    28
    Views
    3,972

    My PA20 single groove pulley system would freeze...

    My PA20 single groove pulley system would freeze up when the temperatures were well below freezing... bought the old school cloth electrical tape...same stuff piper used to tape the wiring to the...
  25. Replies
    19
    Views
    2,176

    Gami...was going to suggest it... sounds like...

    Gami...was going to suggest it... sounds like youíve checked all the trouble shooting boxes... if you donít have any other modifications to the baffles or modifications to increase the differential...
Results 1 to 25 of 274
Page 1 of 11 1 2 3 4