Search:

Type: Posts; User: skywagon8a

Page 1 of 20 1 2 3 4

Search: Search took 0.17 seconds.

  1. Replies
    369
    Views
    47,712

    Charlie, Is that extra length just slid on to...

    Charlie, Is that extra length just slid on to increase the wall thickness in the lower end?
    This is reminding me of long ago in the early 60s (1963?) at GBR. There were a half a dozen 450 Stearmans...
  2. Replies
    17
    Views
    948

    My Cub has the stock tail wire setup and the long...

    My Cub has the stock tail wire setup and the long flaps with a rock solid tail. I think that it is the long flaps eliminating turbulence from the outboard end of the stock flaps reaching the tail...
  3. Replies
    2
    Views
    117

    option 3 This is my BC Cub...

    option 3
    This is my BC Cub https://www.supercub.org/forum/showthread.php?42657-New-Smith-Cub-coming-together&highlight=smith+cub
    Unfortunately the photobucket logo is bluring the pictures but...
  4. Replies
    12
    Views
    678

    Steve, that failure is screaming for an...

    Steve, that failure is screaming for an explanation. Was it a bad casting? Do they use an inferior alloy for casting? Was the mating surface not machined flat? Was the mating to the engine not...
  5. Replies
    16
    Views
    670

    The PMA only means that the parts are approved as...

    The PMA only means that the parts are approved as designed and authorized to be manufactured. It Does not authorize the installation on any airplane.
  6. Replies
    1,450
    Views
    352,111

    " Hey we have a beautiful GPS system with moving...

    " Hey we have a beautiful GPS system with moving map in our airplane, lets go flying in the unlit mountains after dark under an unknown overcast. Let's take the Navajo, it goes fast so it won't take...
  7. Just to stir the pot, I've flown several J-5s...

    Just to stir the pot, I've flown several J-5s with 0-235s, they were decent but just so so. Then once I was asked to ferry a no interior 85 hp J-5. That airplane was amazing, very short take off and...
  8. Replies
    16
    Views
    801

    This is a good article on checking your fuel...

    This is a good article on checking your fuel nozzles and how to determine if they have different flow between them. The author is retired from Lycoming....
  9. Replies
    24
    Views
    1,293

    There's plenty of open water around here. We...

    There's plenty of open water around here. We should consider meeting at Island Bob's in the spring. Was your DPE Doug Smith? He was F/E for me on the 727.
  10. Replies
    61
    Views
    2,544

    This is true however, the tail authority is...

    This is true however, the tail authority is greater and the drag component is less with the ballast.
  11. Replies
    24
    Views
    1,293

    Tom, I'm not aware of there being any issues with...

    Tom, I'm not aware of there being any issues with it's placement. It feels very comfortable blowing on your feet and the output openings are controllable.
    The only issues we had was before the...
  12. Replies
    24
    Views
    1,293

    So what is wrong with the heater? I know you have...

    So what is wrong with the heater? I know you have one, or at least there was one there.
  13. Replies
    22
    Views
    999

    Adam, Since you do not have an unlimited budget...

    Adam, Since you do not have an unlimited budget you will be money ahead going with Javron over Cub Crafters.
  14. Doug, Your example has backed up my theory that...

    Doug, Your example has backed up my theory that there is a "drag" wall which occurs around 110 mph. Below that speed the drag portion of aerodynamics does not have the same effect as it does over 110...
  15. Replies
    61
    Views
    2,544

    Due to the angle of attack and the inaccuracy of...

    Due to the angle of attack and the inaccuracy of the airspeed in those conditions it is not possible to determine any difference in speed. Without the ballast there was not enough up elevator to get...
  16. Replies
    61
    Views
    2,544

    Denny, Trimming will relieve the stick pressure...

    Denny, Trimming will relieve the stick pressure but not reduce the down force applied by the tail assembly. This in turn equates to an equivalent amount of additional weight which the wing must...
  17. Replies
    16
    Views
    801

    Alternatively to the GAMI route, you can go to...

    Alternatively to the GAMI route, you can go to https://airflowperformance.com/. This is what I did. They modified my nozzles with removable orifices so that they can be fine tuned for much less...
  18. Replies
    16
    Views
    801

    Not so. You are mixing carburetor and fuel...

    Not so. You are mixing carburetor and fuel injection trouble shooting issues. The fuel is evenly distributed from the flow divider depending on the orifice size of the discharge nozzles which are in...
  19. Replies
    16
    Views
    801

    Without knowing the exact numbers for this model...

    Without knowing the exact numbers for this model engine. those fuel flow numbers sound about right.


    At what OAT? Other than a high OAT you may have leaned the mixture too much or the baffles...
  20. Replies
    148
    Views
    6,973

    Which frequency is your equipment operating on,...

    Which frequency is your equipment operating on, 978 mhz or 1090 mhz? It is my understanding that only the 1090 mhz units talk to each other. The 978 mhz units have to communicate through a ground...
  21. Replies
    45
    Views
    10,615

    Does it matter what material this fairlead is...

    Does it matter what material this fairlead is made from? Would it make a difference if it was wood, phenolic, teflon or some other material? Perhaps we should consider changing the materiel that this...
  22. Replies
    45
    Views
    10,615

    If you live in dry country galvanized will do. In...

    If you live in dry country galvanized will do. In high humidity and coastal regions when kept outside the portions exposed to the elements can rust. If the rust forms on the inner portions the cable...
  23. Replies
    23
    Views
    1,173

    Charlie, get a Diehard from Sears. I have one in...

    Charlie, get a Diehard from Sears. I have one in my Kubota that is 25+ years old, sits for weeks at a time....hasn't let me down yet. Have a Diehard in the 185 as well. ;-)
  24. Replies
    601
    Views
    101,679

    I saw that on amphib floats at a Cranland...

    I saw that on amphib floats at a Cranland breakfast last year. It had a bad shimmy with the nose wheel on take off which needed attention. I heard that it is based in PLY?
  25. Replies
    8
    Views
    363

    Paint a radial stripe on your tire. Then you can...

Results 1 to 25 of 500
Page 1 of 20 1 2 3 4