Search:

Type: Posts; User: behindpropellers

Page 1 of 20 1 2 3 4

Search: Search took 0.89 seconds.

  1. Replies
    12
    Views
    2,242

    He probably bent the stud sticking out of the...

    He probably bent the stud sticking out of the firewall. Not sure how I would know that :oops:
  2. Replies
    30
    Views
    1,199

    I know weight reduction is serious business in...

    I know weight reduction is serious business in airplanes, but don't discount reliability when you are on your quest to save weight.

    Tim
  3. Replies
    40
    Views
    2,072

    PMA - Approval to manufacture a part. TSO -...

    PMA - Approval to manufacture a part.

    TSO - Broad approval that an article meets requirements to be installed in a product (airplane)

    So.... I can see saying an install is minor if it meets TSO...
  4. Replies
    11
    Views
    808

    Can you imagine all of the people driving cars...

    Can you imagine all of the people driving cars around who can't read a map that will be lost when they disable GPS!
  5. Replies
    40
    Views
    2,072

    I don't understand you comments. The FAA has...

    I don't understand you comments. The FAA has relaxed quite a bit on safety enhancing devices. As far as your comments go: It is expensive and time consuming to develop and build this stuff. Test it...
  6. Replies
    37
    Views
    2,779

    Are you going to give Kevin's wife a purse if he...

    Are you going to give Kevin's wife a purse if he shows up? Gucci? Coach?
  7. Replies
    40
    Views
    2,072

    Blahhhh.... What happens when Garmin is the...

    Blahhhh....

    What happens when Garmin is the only player. We need uavonix, electronics international, jpi, and others.
  8. Replies
    16
    Views
    901

    Perhaps a good re-use of a venturi is a relief...

    Perhaps a good re-use of a venturi is a relief tube, then.
  9. Replies
    40
    Views
    2,485

    Thought about it but its already a lot of...

    Thought about it but its already a lot of overhung load on the carburetor.
  10. Replies
    16
    Views
    901

    Rich, Yep. 1957 172. Learned on those ancient...

    Rich,

    Yep. 1957 172. Learned on those ancient instruments...


    Tim
  11. Replies
    16
    Views
    901

    Took my instrument check ride in the airplane you...

    Took my instrument check ride in the airplane you describe and also put about 25 hours on it in the clouds.

    Tim
  12. Grant, Check these guys out: ...

    Grant,

    Check these guys out:

    https://www.schallercorporation.com/plastic-boxes/

    Tim
  13. Replies
    29
    Views
    1,323

    I have a Mr. Heater like that in my garage. Great...

    I have a Mr. Heater like that in my garage. Great service from Mr. Heater. Control board in it went out, they sent a new one no questions asked.

    Tim
  14. Replies
    29
    Views
    1,323

    Sorry I left that detail out, this line is to get...

    Sorry I left that detail out, this line is to get from the tank to my hanger, it will be inside the building in the rafters.

    Tim
  15. Replies
    29
    Views
    1,323

    Hanger Heat

    Want to add heat to my hanger.

    1. I have to run a propane line around 100' or so. Is there anything besides black pipe that I can use?

    2. Any furnace advice? Its just a T hanger, relatively...
  16. Replies
    90
    Views
    5,499

    Curious - Is this done via FA or another STC or?

    Curious - Is this done via FA or another STC or?
  17. Replies
    4
    Views
    312

    You should be able to get it if you are using the...

    You should be able to get it if you are using the correct relations in your sketch. What year of Solidworks are you using?

    Tim
  18. Replies
    37
    Views
    2,779

    Running the 340 in the heavy class?

    Running the 340 in the heavy class?
  19. Replies
    33
    Views
    1,750

    Few Questions: 1. Do you want to build or fly?...

    Few Questions:

    1. Do you want to build or fly?
    2. Is light sport a requirement?
    3. Where are you located?
  20. Replies
    41
    Views
    3,446

    Also.... You should be able to nail your speeds...

    Also.... You should be able to nail your speeds for downwind, base, and final. Think of your downwind as the foundation for your landing. If you don't build on a good foundation, everything falls...
  21. Replies
    90
    Views
    5,499

    Hi Stewart, My comment was not from recent...

    Hi Stewart,

    My comment was not from recent personal experience. Mostly from reading threads on Beechtalk. Beechtalk is free, just sign up.

    I would not buy new from continental:



    Tim
  22. Replies
    90
    Views
    5,499

    I would not buy a new or reman from continental...

    I would not buy a new or reman from continental right now.
  23. Replies
    10
    Views
    753

    Impeccable timing. Same oring just failed on my...

    Impeccable timing. Same oring just failed on my dipstick.

    Thanks Kirby.
  24. Replies
    100
    Views
    7,228

    Thinking about just calling them up every time I...

    Thinking about just calling them up every time I want to go fly...
  25. Dave, I don't think you have any idea what it...

    Dave,

    I don't think you have any idea what it really costs to build a kit.

    Tim
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4