Search:

Type: Posts; User: ron

Page 1 of 16 1 2 3 4

Search: Search took 0.19 seconds.

  1. Replies
    18
    Views
    3,906

    All great ideas.Think I will use nut plates...

    All
    great ideas.Think I will use nut plates wherever I can tho!
  2. Replies
    104
    Views
    23,679

    Hi stewartb ,Are you saying lay a level on the...

    Hi stewartb ,Are you saying lay a level on the top cowl it should show level in the fore /aft.My nose bowl would be approx 2.5 ” higher than the top of the boot cowl in the 3 point attitude
    !.To...
  3. Replies
    104
    Views
    23,679

    Thanks Stewartb,I hate to admit it but me thinks...

    Thanks Stewartb,I hate to admit it but me thinks you are right.I do like the inflight characteristics of the mount I have, but it is a right arsehole on the ground.I have flown quite a few types of...
  4. Replies
    104
    Views
    23,679

    Thanks for the reply.Trim is used variably...

    Thanks for the reply.Trim is used variably depending on load on Takeoff,on landing trim out the control forces for the lowest speed to flare.Most strips are rough and relatively short average 800 ft.
  5. Replies
    104
    Views
    23,679

    My question: Have a backcountry cub,3” gear...

    My question: Have a backcountry cub,3” gear extension,29” alaskan bush wheels,thrustline modification.Whilst tail wheel is on the ground the visibility over the nose is not good.My head is almost in...
  6. Replies
    2
    Views
    631

    Thanks Bob,I should have checked this prior to...

    Thanks Bob,I should have checked this prior to writing.The water was in the fuselage, not the stab.All drAIN HOLES BLOCKED!
  7. Replies
    2
    Views
    631

    Stabiliser drain holes.

    After a heavy rain my friends Cessna 180A holds several quarts of water in the stabiliser, trim at neutral.This can be considered B dangerous.
    IDEAS?
  8. Further to my Query, with a full flap approach...

    Further to my Query, with a full flap approach would you guys say the aircraft requires much more power ? Does this situation improve stability?
  9. Alaskan fowler flaps and inline engine thrust mounts

    Has anyone a combination of the above.What effect do the flaps have on the approach trim etc?
  10. Replies
    12
    Views
    1,929

    found mine clogged by a rag after a full rebuild...

    found mine clogged by a rag after a full rebuild about 15 years back.I was not impressed!
  11. Thread: AN bolt supplier

    by ron
    Replies
    38
    Views
    4,905

    many thanks Mike,still cannot get the required...

    many thanks Mike,still cannot get the required bolts!
  12. Thread: AN bolt supplier

    by ron
    Replies
    38
    Views
    4,905

    Even with a prop Pete?

    Even with a prop Pete?
  13. Thread: AN bolt supplier

    by ron
    Replies
    38
    Views
    4,905

    Hi 46 cub.As per my letter thank you.They replied...

    Hi 46 cub.As per my letter thank you.They replied none in stock yet I saw that figure you quoted??!!
  14. Thread: AN bolt supplier

    by ron
    Replies
    38
    Views
    4,905

    Hi Irishfield ,Thanks for your reply which we...

    Hi Irishfield ,Thanks for your reply which we find interesting that one bolt has a damaged thread.Most of mine have damaged threads after withdrawing the rusted bolts from the lugs.One bolt actually...
  15. Thread: AN bolt supplier

    by ron
    Replies
    38
    Views
    4,905

    will try and post a picture.Yes the thread on the...

    will try and post a picture.Yes the thread on the bolts supplied have a longer thread but an An bolt would suffice as the lugs provided had a very short thread length.
  16. Thread: AN bolt supplier

    by ron
    Replies
    38
    Views
    4,905

    probably had nothing then!Mike your knowledge...

    probably had nothing then!Mike your knowledge would probably lead me to a distributer of big AN bolts.Can you help please?
  17. Thread: AN bolt supplier

    by ron
    Replies
    38
    Views
    4,905

    Think they could be the supplier to Prince...

    Think they could be the supplier to Prince props.They are non certified bolts and probably zinc coated.The bolts corroded badly in the sockets.One sheered off on undoing bolts.This time it will be AN...
  18. Thread: AN bolt supplier

    by ron
    Replies
    38
    Views
    4,905

    AN bolt supplier

    Anyone out there know a supplier of long AN bolts for a Prince propeller.Unfortunately the bolts supplied were not of a standard we were happy with .The bolts we require are AN8H-53A.Seems very hard...
  19. Replies
    14
    Views
    2,465

    Hi SD Cubman. Did you retrofit that mount or did...

    Hi SD Cubman. Did you retrofit that mount or did you fit it on initial build?If it was a retrofit would be interested what changes noticed with the inline lowered.
  20. Area rule ?

    Area rule ?
  21. Replies
    14
    Views
    2,465

    Thanks everyone for the replies.Pete,the info is...

    Thanks everyone for the replies.Pete,the info is on the Javron website for the PA-18 super cub order form.Mike I have slicks and not going to change!.Have an outback super cub, inline thrust built...
  22. Replies
    14
    Views
    2,465

    Am surprised no one has fitted these mounts.

    Am surprised no one has fitted these mounts.
  23. Replies
    14
    Views
    2,465

    Javron lowered engine mounts.

    Hi All ,Would be interested to hear from people who have fitted the Javron lowered engine mounts.How did they affect performance,visibility and appearance.Thanks,Ron.
  24. Replies
    17
    Views
    1,831

    have ordered a new sensor but seems Dynon...

    have ordered a new sensor but seems Dynon presently working from home during virus.Will put in a temporary analogue job in series.Thanks all for help.Will advise.
  25. Replies
    17
    Views
    1,831

    yes

    yes
Results 1 to 25 of 383
Page 1 of 16 1 2 3 4