Search:

Type: Posts; User: Hyrdflyr

Page 1 of 11 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    11
    Views
    1,708

    I have a crossover set from an 0290 tripacer but...

    I have a crossover set from an 0290 tripacer but no muffler. Would they fit?
    Hyrdflyr

    Sent from my R1 PLUS using SuperCub.Org mobile app
  2. A good read: ...

    A good read: https://www.youtube.com/watch?v=rGdCVoGibXE
  3. Replies
    5
    Views
    460

    I tried to use the PA-20/22 crossover pipes with...

    I tried to use the PA-20/22 crossover pipes with my PA-12 per the Kenmore STC and couldn't make it work. Went back to the old exhaust headers from my old 0-290 installation. They are the same...
  4. Replies
    18
    Views
    672

    Not to denigrate some admittedly cool and very...

  5. Replies
    21
    Views
    1,850

    I think I saw a similar engine on some military...

    I think I saw a similar engine on some military target drones about 60 years ago. I think McColough made some of them.


    Sent from my R1 PLUS using SuperCub.Org mobile app
  6. Replies
    4
    Views
    545

    PM me please, John

    PM me please, John
  7. Replies
    45
    Views
    3,596

    I can't t speak to why one venue grows and...

    I can't t speak to why one venue grows and another deminishes, but...

    It's been pointed out before that we have effectively locked out most of the kids and adults who might have been interested in...
  8. Years ago I lived in Alpine WY, in fact worked...

    Years ago I lived in Alpine WY, in fact worked for the contractor who built the runway. I kept a calendar weather diary that winter. Due to the "lake effect" from Palisades Reservoir, It snowed...
  9. Replies
    11
    Views
    933

    A lot of 12s did not have header tanks. It is...

    A lot of 12s did not have header tanks. It is usually outside the cabin under the left side cowl since there is no room otherwise in the cockpit. Usually there will be/should be an on/off stopcock...
  10. Replies
    1,325
    Views
    331,930

    The FAA probably won't have time to put them out...

    The FAA probably won't have time to put them out of business. Their insurance company will more than likely pull the plug first. Their rates will go up to where it will be impossible to operate. ...
  11. Thread: Spark plugs

    by Hyrdflyr
    Replies
    63
    Views
    5,512

    spark plug ohm meter

    As long as you are going to buy a multimeter, might as well get one that reads DC amps like the one Mike suggests. Very good for troubleshooting electrical systems. Most multimeters do not work on...
  12. Replies
    13
    Views
    1,431

    I use only Polar wire connectors. Great service...

    I use only Polar wire connectors. Great service and good pricing too. Their connectors are mil spec and are the best thing going for aircraft , boats or whatever. Buy good crimpers from them also. ...
  13. Replies
    26
    Views
    8,739

    SeeW Sent from my R1 PLUS using SuperCub.Org...

    SeeW

    Sent from my R1 PLUS using SuperCub.Org mobile app
  14. Thread: Intro

    by Hyrdflyr
    Replies
    21
    Views
    1,930

    Flydipper. PM me. I'm in Anacortes rebuilding...

    Flydipper. PM me. I'm in Anacortes rebuilding my 12 and have probably all the STC info and plans you might need..(except the left hand door)

    another John
  15. Thread: PA-12 Build

    by Hyrdflyr
    Replies
    77
    Views
    22,372

    The other day I needed to install a circle clip...

    The other day I needed to install a circle clip on a fairlead in an un-handy place. I got a pair of spreader pliers with the small pins used for drilled circle clips, put them inside the fairlead...
  16. Replies
    14
    Views
    2,823

    I used aftermarket interiors on several C207s...

    I used aftermarket interiors on several C207s that I was maintaining. Can't remember the manufacturer but they were slightly heavier and 3 times tougher. Didn't always fit perfectly but neither did...
  17. Replies
    14
    Views
    1,605

    I welded some small steel tabs on the tubing...

    I welded some small steel tabs on the tubing before I media blasted and epoxied and then screwed the channel onto the tabs. Doesn't take long and takes care of the problem. Plus its a lot easier...
  18. My home base is in Banner. Don't have it handy...

    My home base is in Banner. Don't have it handy but recently got a mailed flyer from an IA who had cub experience and had a shop at the Buffalo airport. Plus, There's a maintenance guy at the Casper...
  19. Replies
    15
    Views
    3,154

    Where do you get an 8 amp alternator, and is it ...

    Where do you get an 8 amp alternator, and is it a field approval?
  20. Atlee tank stc calls for , I believe, silicone...

    Atlee tank stc calls for , I believe, silicone calling as adhesive to hold the fabric tight to the bottom of the tank. I'll check the stc instruction manual if anyone needs the info

    Sent from my...
  21. Replies
    72
    Views
    20,619

    PA-18 flap handle drawing

    Thanks, Mike, it is the 2 5/16 inch dimension I needed.:lol:
  22. Replies
    72
    Views
    20,619

    My problem is that I moved my project 2000 miles...

    My problem is that I moved my project 2000 miles and lost the old flap handle arm somewhere along the way....I think it's about 4 inches or so but would just as soon get it right on. I have the same...
  23. Replies
    72
    Views
    20,619

    Flap installation particulars

    Hi Mike, I had to install my flap handle and shaft mount on my new to me 12 airframe. Got out my Sullivan flap installation STC plans from the logs and reproduced the original installation. ...
  24. Thread: Rivet pitch ?

    by Hyrdflyr
    Replies
    17
    Views
    3,373

    A question. My old boot cowl flange is on the...

    A question. My old boot cowl flange is on the inside (rear) of the firewall. I always figured that there was less chance of intrusion from fire or lubricants that way. Besides it looks nice when you...
  25. Replies
    40
    Views
    8,333

    It's not just the weight of the cooler that needs...

    It's not just the weight of the cooler that needs to be considered, but the weight of the oil in the cooler and lines also that will shift the cg further than 1/16 of an inch.[emoji1]

    Sent from...
Results 1 to 25 of 266
Page 1 of 11 1 2 3 4