Search:

Type: Posts; User: J4coupe

Search: Search took 0.00 seconds.

  1. Replies
    14
    Views
    836

    The nut that holds the gear on is not flat where...

    The nut that holds the gear on is not flat where it mates with the gear. It has a lip that recesses into the gear.
  2. Replies
    14
    Views
    836

    All sorted now. No radio interference and easy...

    All sorted now. No radio interference and easy starting. Lapping was not an option on the 4334 kit. The pin hole will line up within the torque values. Luckily the 4334 kit comes with its own...
  3. Replies
    1
    Views
    238

    J4 Help. Identify the Part

    Can anyone identify the item in the picture. I am trying to rebuild a basket case J4 and have started covering. The control cables have just gone in. I am sure it holds a cable guide but I have no...
  4. Replies
    14
    Views
    836

    Thanks. On the case now.

    Thanks. On the case now.
  5. Replies
    14
    Views
    836

    I bought a kit that consists of the 2 slick mags...

    I bought a kit that consists of the 2 slick mags (4333), harness and 2 gears. The 2 gears supplied are different to the original and do away with the need for spacers.
  6. Replies
    14
    Views
    836

    Thanks Glenn I think we have talked before. I...

    Thanks Glenn
    I think we have talked before. I am rebuilding a J4 Coupe over here in the UK.
    Roger
  7. Replies
    4
    Views
    315

    Thanks. As above I found L-1499 just after...

    Thanks. As above I found L-1499 just after submitting the post.
  8. Replies
    4
    Views
    315

    TYPICAL. I did spend quite a while on GOOGLE and...

    TYPICAL. I did spend quite a while on GOOGLE and found 1499 just after my post.
    Thanks for the info.
    Roger
  9. Replies
    14
    Views
    836

    Magneto Drive Gear

    Hi
    I am replacing the Eisemann Magnetos on my A65 with Slick 4333. I cannot find any information on the torque value for the drive gear retaining nut. Also should the gear have a bit of end play....
  10. Replies
    4
    Views
    315

    Ignition Lead Assembly

    Hi
    I am looking for a copy of the Unison L-1178 Ignition Lead Assembly & Installation Manual. Can anyone help please.Thanks
    Roger
  11. Thread: J4 pitot tube

    by J4coupe
    Replies
    4
    Views
    1,587

    Thank Glenn, that sounds about right as it would...

    Thank Glenn, that sounds about right as it would be the same as the pitot pipe on the jury strut.
  12. Thread: J4 pitot tube

    by J4coupe
    Replies
    4
    Views
    1,587

    J4 pitot tube

    Does anyone know the internal diameter of the aluminium tube that runs in the wing of the J4?

    Thanks

    Roger
  13. Replies
    8
    Views
    2,987

    Thanks Glenn. I have the one from Univair which...

    Thanks Glenn. I have the one from Univair which looks the same.
    Roger
  14. Replies
    8
    Views
    2,987

    Thanks all for the great responses. I have...

    Thanks all for the great responses. I have emailed gvance2 and also ordered some alternate part to see how they fit. If there are any other J4 owners that can help with info on the J4 I would...
  15. Replies
    8
    Views
    2,987

    Help Find a Seal

    Hi
    Has anyone any idea on where I get some of these seals. This is the seal in the oleo of the J4 Coupe. The identification number on it is VICTOR 62020. I am hoping that it was a standard part used...
  16. Replies
    2
    Views
    1,541

    J4 Undercarriage

    I am overhauling the undercarriage on my J4A (As well as everything else). I have found springs broken and internally they are a bit of a mess. I did read in a forum somewhere that someone replaced...
Results 1 to 16 of 16