Search:

Type: Posts; User: Fortysix12

Page 1 of 20 1 2 3 4

Search: Search took 0.19 seconds.

  1. Replies
    99
    Views
    16,501

    Couple of notes about my experience with...

    Couple of notes about my experience with installing Experimental super cub servos. I had visited Airtronics, Billings MT, and observed the professional installation of a roll servo. One point that...
  2. Replies
    99
    Views
    16,501

    Check the older S-TEC's STC's

    Check the older S-TEC's STC's
  3. Thanks for the input. I will check out the other...

    Thanks for the input. I will check out the other related thread. I haven't purchased the motor mount yet. This an experimental conical application so i would think the motor mount is ready to go and...
  4. Does the O360 Fit inside a standard 150 HP Cowling

    I realize there are lots of 180HP PA 18s, but was curious what mods if any are required to install the O360 into the standard 150 Cub with regards to fitting. Sutton Exhaust if possible but could go...
  5. Thread: Hydrasorbs

    by Fortysix12
    Replies
    2
    Views
    608

    sent you a PM

    sent you a PM
  6. Steve, Who is " forcing them to become tail...

    Steve,

    Who is " forcing them to become tail drag pilots"?
  7. will these fit a CC11 160 Carbon Cub?

    will these fit a CC11 160 Carbon Cub?
  8. Replies
    2
    Views
    413

    FS: I"m interested , send me a PM with contact

    I"m interested , send me a PM with contact
  9. Replies
    26
    Views
    1,512

    Sent you a private message

    Sent you a private message
  10. Replies
    26
    Views
    1,512

    One other thought. Might consider purchasing a...

    One other thought. Might consider purchasing a set of Plans from Wag Aero, say a Sportman 2+2 plans, a different airplane than a Super Cub but the plans will show how some of the basic wood jig...
  11. Replies
    26
    Views
    1,512

    What is the motivating factor to build from...

    What is the motivating factor to build from scratch. It is a long road if even if you work at it at a steady pace. The drawings combined with Christian's web site Supercubproject.com is a must...
  12. Replies
    145
    Views
    17,069

    I've been told that 50% of Huskies have been on...

    I've been told that 50% of Huskies have been on there nose as a direct result of toe brakes. Might be a bit exaggerated but they are notorious for going over. In an effort to help the situation...
  13. Replies
    16
    Views
    1,301

    I don't think there is a wrong answer for salvage...

    I don't think there is a wrong answer for salvage calipers. They just have to fit the gear plate,align and clear the tire. mounting bolts differ from a stock cub gear from say what used. I used the...
  14. Replies
    5
    Views
    688

    Configure your throttle set up with a long...

    Configure your throttle set up with a long inexpensive lawnmower cable or piano wire. Then order it. fitting to fitting is what you are after. This will give you the option to run it where you want...
  15. So I'd start here. Consider it a guide for what...

    So I'd start here. Consider it a guide for what not to do.

    https://www.ntsbreporter.us/
  16. Replies
    52
    Views
    10,253

    Great link Steve. For our trip from Florida to...

    Great link Steve. For our trip from Florida to Montana last summer we decided only to land on grass regardless of whether there was a grass strip or not. It was a lot of fun. At low use...
  17. Replies
    6
    Views
    1,439

    Skywagon8a, You are correct. To be honest this...

    Skywagon8a, You are correct. To be honest this was a semi temporary configuration but it worked out so well I never changed it. One reason for minimizing the support structure is because the angle...
  18. Replies
    6
    Views
    1,439

    Wholly smoke. I got nothing. That thing is very...

    Wholly smoke. I got nothing. That thing is very impressive. https://youtu.be/fK67j2HKkqc
    But there is one little difference. $8K vs $800K :)
  19. Replies
    6
    Views
    1,439

    Mowing my 6 acre runway in 32 minutes

    A faster better way to get it done. The entire rig was under 10K and works very well. I cut at the maximum recommended speed published by the Swisher manufacture which is around 5 mph.
    ...
  20. Replies
    15
    Views
    2,504

    So if you want an 80 or 90 degree hangar,...

    So if you want an 80 or 90 degree hangar, Icynene the ceiling, Glue 2 inch styrofoam 8 x 10 x 2 inch panels on the door and install a 3 ton minisplit. You will be very happy. Oh,
    The building must...
  21. Curious what your thoughts are?

    Curious what your thoughts are?
  22. Replies
    31
    Views
    14,652

    Here is an informative video. Why Are True...

    Here is an informative video.


    Why Are True Airspeed And Indicated Airspeed Different? - Bing video
  23. Minimum controlled airspeed.

    Minimum controlled airspeed.
  24. I think you are just experiencing the new normal...

    I think you are just experiencing the new normal with the VGs. They are allowing the airplane to fly slower Go work the MCA. Get a feel for the elevator load at level mca. Then add power for a slight...
  25. Replies
    8
    Views
    1,816

    decided no need for the switch , breaker only ,...

    decided no need for the switch , breaker only , always on.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4