Search:

Type: Posts; User: Steve Pierce

Page 1 of 20 1 2 3 4

Search: Search took 2.86 seconds.

  1. Replies
    19
    Views
    5,459

    Like this. 58075

    Like this.
    58075
  2. Replies
    19
    Views
    5,459

    You could do like this guy but looks pretty...

    You could do like this guy but looks pretty amateurish to me. I would just use beaded from the master cylinder to the gear leg and if needed, bottom of gear leg to the caliper. There are Weatherhead...
  3. Replies
    48
    Views
    2,653

    Usually when the diaphragm goes it bursts and...

    Usually when the diaphragm goes it bursts and runs fluid all over the floor board.
  4. Replies
    1
    Views
    335

    1982 PA18 160hp Restored $275K

    I figure the headline will get some attention and start some controversy. This is a 1982 model PA18-150 upgraded to 160 hp. Out of rebuild 2 years at the end of this month and rebuilt LyCon engine...
  5. Replies
    6
    Views
    375

    I made Tal do that. All the others that I have...

    I made Tal do that. All the others that I have done where at rebuild and those tubes are easy to pull out when the cylinder isn't installed.
  6. Replies
    6
    Views
    375

    I saw that, I want the one that shows sold for...

    I saw that, I want the one that shows sold for $35. :lol:
  7. Chris, I know you are a romantic but romance...

    Chris, I know you are a romantic but romance doesn't pay the bills. I am sure you could raise a good bit of money with a Go-Fund me but I doubt it would be as much as you could get for the airplane...
  8. Replies
    5
    Views
    708

    Looks like someone modified a J3 fuselage to me....

    Looks like someone modified a J3 fuselage to me. Door attachment, rear of top deck aft of the wing attachment, rear seat and other structures. Heavily modified.
  9. Replies
    6
    Views
    375

    That is slick. I have installed a lot of those...

    That is slick. I have installed a lot of those kits but have never seen the inside tubing cutter. Gotta find one now. Yes, I am a tool junky. ;)
  10. Replies
    1
    Views
    272

    Sal's Aircraft Cylinders 972-346-3339 Gibson...

    Sal's Aircraft Cylinders 972-346-3339

    Gibson Aviation https://gibsonaviationok.com/
  11. Replies
    34
    Views
    1,083

    Before you do anything find out if it does it...

    Before you do anything find out if it does it again and under what conditions. I had a Super Cub that I had recovered do this after we brought it to Texas from Florida and then it went to the midwest...
  12. Replies
    27
    Views
    11,166

    Look at the Lycoming O-320 Type Certificate Data...

    Look at the Lycoming O-320 Type Certificate Data Sheet and see what the difference in the engine model you have and the one certified on your airplane. A lot of time it is a simple to change the...
  13. Replies
    18
    Views
    813

    Once you got it set up did you find you had to...

    Once you got it set up did you find you had to adjust it again under different conditions. I admit it is a pain to go into the settings and set it up. I did it initially and haven't messed with it...
  14. Replies
    8
    Views
    677

    And the poster promoting the Beringer gear...

    And the poster promoting the Beringer gear groundlooped both his Carbon Cubs with said gear. The one he sold came to my neck of the woods and a very competent instructor I know removed it and put the...
  15. What is the oil consumption? What are the...

    What is the oil consumption? What are the compressions and where is the air leaking? What does a borescope inspection show you? What does inside the valve covers look like? Lyconings don't normally...
  16. Replies
    18
    Views
    813

    Interesting, I have done 3 lately including my...

    Interesting, I have done 3 lately including my own and thought they all sounded great and were easy to set up. Of course Cathy says I can't hear lots of things but I thought that was her just nagging...
  17. Replies
    18
    Views
    1,100

    I have cutouts and play with them on the blank...

    I have cutouts and play with them on the blank panel prior to cutting.
  18. Replies
    18
    Views
    1,100

    Scott, some good layouts here....

    Scott, some good layouts here. https://www.supercub.org/forum/showthread.php?54930-Cgr-30-p
  19. Replies
    18
    Views
    813

    The intercom works great but the VOX can activate...

    The intercom works great but the VOX can activate when the window and door are open and your passenger doesn't keep their mic out of the in coming air so I install the switch to use either VOX or...
  20. Replies
    15
    Views
    1,162

    My brother's 90 hp bar hopping J3. 57984 57985

    My brother's 90 hp bar hopping J3.
    57984

    57985
  21. Replies
    15
    Views
    1,162

    Clipped Wing Cub I rebuilt for Todd Peterson....

    Clipped Wing Cub I rebuilt for Todd Peterson.
    57982

    57983
  22. Replies
    18
    Views
    813

    I have used them in the last three Super Cub...

    I have used them in the last three Super Cub rebuilds and multiple panel upgrades including my own Super Cub. Com, Transponder and ADSB. I just have the Com and really like it. Monitoring two...
  23. Replies
    8
    Views
    744

    WTB: Most of the nice Super Cubs I have been involved...

    Most of the nice Super Cubs I have been involved with lately never made the open market. All word of mouth. I had a dealer contact me with two high end Super Cubs. I checked out what I could...
  24. Replies
    8
    Views
    744

    WTB: What is your budget?

    What is your budget?
  25. I have a pair of brand new Scott brake cylinders,...

    I have a pair of brand new Scott brake cylinders, a used set with North River boosters and probably a stock set with diaphragms. Message me what you think they are worth.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4