Search:

Type: Posts; User: aeroaddict

Page 1 of 5 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    22
    Views
    762

    Certainly not an expert but are the bubbles...

    Certainly not an expert but are the bubbles uniform across the surface, or does the concentration of bubbles vary? If they are uniform, then that could be paint, if not uniform, them possible surface...
  2. Replies
    67
    Views
    9,721

    Dang, sharp looking plane there. You probably...

    Dang, sharp looking plane there.

    You probably know this trick for rock chips on the gear, but I have applied the 3M clear auto protective film to my gear and leading edge of the horizontal stab....
  3. Replies
    67
    Views
    9,721

    Thanks. Went on their (Acme's) website and didn't...

    Thanks. Went on their (Acme's) website and didn't see anything, but I do now see the pro series even though they have not uploaded information about the pro series.

    Good thing I have Gen3 as I'm...
  4. Replies
    67
    Views
    9,721

    So what is the difference between Gen3 and Gen4?...

    So what is the difference between Gen3 and Gen4? I thought the only difference was the STC? And are you using Acme's new gear legs?
  5. Replies
    145
    Views
    6,985

    I should have stated that I choose not to leave...

    I should have stated that I choose not to leave the heater on and burn gobs of propane since I could do other tasks during winter.

    The point being, you will need a warm place to do covering in.
  6. Replies
    145
    Views
    6,985

    Your profile doesn't say where you are located,...

    Your profile doesn't say where you are located, but when covering mine with Poly Fiber, winter didn't work well for covering as the temps were not warm enough (even with a heated hanger).
  7. Replies
    145
    Views
    6,985

    I thinking 3 pages on this thread.

    I thinking 3 pages on this thread.
  8. Replies
    8
    Views
    683

    Ya know, I wore a motorcycle helmet when it...

    Ya know, I wore a motorcycle helmet when it wasn't required by law. I also rode for over 40 years (sport bikes) never in shorts or flaps even though it was hot!

    Now flying my "armature" built...
  9. Replies
    8
    Views
    683

    Must be a model change coming up. Didn't see any...

    Must be a model change coming up. Didn't see any deals on Amazon.
  10. Replies
    67
    Views
    9,721

    Ha! Yup, I have Amce's on my old legacy death...

    Ha! Yup, I have Amce's on my old legacy death gear. Makes the 'death' a lot softer.
  11. Replies
    8
    Views
    683

    Garmin InReach on sale

    As the title states.
  12. Replies
    33
    Views
    2,095

    Why would that be? Considering EarthX batteries...

    Why would that be? Considering EarthX batteries are for ATV's, UTV's, race cars, motorcycles, sleds (snowmobiles), ...... it would seem they are designed to work with automotive type alternators.
  13. Thanks for the responses. I did search and read...

    Thanks for the responses. I did search and read the results. It was interesting that Pponk' 180's were all different with carb icing and that Continental engines are prone to icing more than the...
  14. Carb Air Temp Sensor: What's the best method?

    Seems like a novice question, and it probably is, but the plane has a Carb air temp gauge (and an OAT).

    When flying older planes, it was the 'use carb heat when reducing throttle to idle'. And of...
  15. Replies
    303
    Views
    15,251

    Ok, I'm going to start a new thread as this one...

    Ok, I'm going to start a new thread as this one has gotten to long.

    New thread: "Dodge pickup death wobble vs legacy death gear"
  16. Replies
    303
    Views
    15,251

    So you are saying I should rotate my tires? Back...

    So you are saying I should rotate my tires? Back to front? :-P
  17. Replies
    303
    Views
    15,251

    "Those CC airplanes sound like pieces of sheet....

    "Those CC airplanes sound like pieces of sheet. The data suggests they turn average pilots into Fuktards. Why would a guy buy one?"

    Well I whish I would have known this before spending 3 years to...
  18. Replies
    303
    Views
    15,251

    Selling it because of the gear? :-P Just kidding,...

    Selling it because of the gear? :-P Just kidding, no flaming please.
  19. Replies
    303
    Views
    15,251

    Dang, that is one clean plane in the pic. Guess I...

    Dang, that is one clean plane in the pic. Guess I better get to work on cleaning mine.
  20. Replies
    303
    Views
    15,251

    "Learning to properly fly a tailwheel aircraft...

    "Learning to properly fly a tailwheel aircraft will have some bumps along the way, better to take the bumps in a 30 grand plane vs a 300 grand one. Once you get a few runway lights and some ditch...
  21. Replies
    88
    Views
    6,532

    I think that is a VERY GOOD POINT. Learn about...

    I think that is a VERY GOOD POINT. Learn about mountain flying it will do you good; winds aloft, weather, mountain waves, DA, .........

    I can land most places, but I have had the cr_p scared out...
  22. Replies
    88
    Views
    6,532

    Great discussion. For tools I think it depends on...

    Great discussion. For tools I think it depends on the plane, food and shelter is a given.

    But what about the choice between a sat phone or the newer sat devices that text, such as the InReach?
  23. Replies
    11
    Views
    761

    Cool idea but I would think you might get...

    Cool idea but I would think you might get aerodynamic interference from the covered struts at high AOA and or flaps deployed.
  24. Replies
    151
    Views
    10,030

    Wow, 3 pages and counting. As a newbie to TW's...

    Wow, 3 pages and counting.

    As a newbie to TW's and Cub's I find this site to be a group of very knowledgeable and no BS people (my kind of people). I have learned immensely from this group and...
  25. Replies
    48
    Views
    3,046

    Good to know about Oratex, it is really...

    Good to know about Oratex, it is really attractive from an application standpoint. I really wanted to try Oratex but could not make it work out. Maybe next plane. :smile:
    Labor time wise, I would...
Results 1 to 25 of 119
Page 1 of 5 1 2 3 4