Search:

Type: Posts; User: Fortysix12

Page 1 of 20 1 2 3 4

Search: Search took 0.33 seconds.

  1. Replies
    31
    Views
    1,851

    I have a 250 W GE mounted so the element is...

    I have a 250 W GE mounted so the element is vertical. Over 1400 hours hung directly in prop blast mounted to my belly pod. Truly amazing. I haven't done a comparison lately but at the time it had...
  2. Replies
    13
    Views
    827

    https://www.lycoming.com/sites/default/files/Engin...

    https://www.lycoming.com/sites/default/files/Engine%20Nameplate%20Replacement.pdf
  3. Replies
    13
    Views
    827

    You are right on Steve! and I went with the...

    You are right on Steve! and I went with the recommendation of a fellow member from Alaska. Great power, runs a little warm but I also run 2500 and up. A great motor for the experimental. The...
  4. Replies
    13
    Views
    827

    Forget the E2D for certificated 18.E2D has a...

    Forget the E2D for certificated 18.E2D has a solid crank,larger sump so needs the O360 type mount if it has the original sump, E2D prop flange has larger bolt studs , and I'm thinking E2D carb...
  5. Replies
    22
    Views
    1,646

    My airplane when loaded at gross requires almost...

    My airplane when loaded at gross requires almost all trim down. I would position the yoke to allow for max pitch down if that is at all possible. When flying lite the trim position is still beyond...
  6. Replies
    43
    Views
    3,060

    Dynon Autopilot

    I used the D10A as my EFIS and two 52's servos. 1500 hours later still going strong. I have photos of the install if anyone needs them. Similar to those already posted. Lou's photos helped me back...
  7. Replies
    70
    Views
    16,145

    Vero beach 18s had the little square window, ...

    Vero beach 18s had the little square window, left .wag aero sells them. They work perfect. I installed one rear right for the passenger and I'm considering adding one right front for dual they...
  8. Replies
    22
    Views
    8,126

    I have found Leak loc for threaded connections -...

    I have found Leak loc for threaded connections - best there is and greatly improved thread lock characteristics.

    Be sure to verify that the two threaded components are in fact NPT, I'm starting...
  9. Replies
    54
    Views
    7,875

    Think in terms of systems,groups. Much like the...

    Think in terms of systems,groups. Much like the piper supercub parts manual
  10. Replies
    40
    Views
    2,292

    Even better and I agree there Mr. Skywagon8a....

    Even better and I agree there Mr. Skywagon8a. Just thinking about establishing a base line for level flight. But you do make a good point.
    On a side note, Every super cub I have ever flown...
  11. Replies
    40
    Views
    2,292

    So raise the tail to level flight and check the...

    So raise the tail to level flight and check the GPM flow at the carb fuel line , then sump then, carb bolt drain plug, do it with the left, right both. Rotate the fuel selector and study the flow....
  12. Replies
    4
    Views
    558

    Thank you for the input. An owner was kind enough...

    Thank you for the input. An owner was kind enough to send me a photo of a 1994 panel and hear it is. With the measurements provided and the photo I am on my way. 44183
  13. Replies
    4
    Views
    558

    Yes photos would be very helpful.

    Yes photos would be very helpful.
  14. Replies
    4
    Views
    558

    Instrument Panel measurement needed

    Converting a 1962 PA 18 panel to a Vero Beach 1993 or 94 style panel and need the top to bottom at center of panel measurement. Standards are 8.5, and 9 inch but I'm thinking these were longer...
  15. Replies
    21
    Views
    1,592

    IO 720 was the worst. Flood. Mixture lean. ...

    IO 720 was the worst.
    Flood.
    Mixture lean.
    Full Throttle.
    Starts 100 % of the time.
    Then perfect and tailor your procedure.
    Electronic ignition is also a game changer.
  16. It's a great post accident review for all...

  17. Replies
    118
    Views
    9,208

    40 x 40 with 2 doors should work ,...

    40 x 40 with 2 doors should work , stagger/canted the airplanes just a little ...
  18. Replies
    5
    Views
    1,299

    FS: One set left.

    One set left.
  19. Replies
    1
    Views
    768

    Yes. Starts, runs. haven't flown. Yet. Noticeable...

    Yes. Starts, runs. haven't flown. Yet. Noticeable mis between right and left mag when checking. More like a tiny lag. Other than that Should be good. Connected Manifold pressure line to one cylinder....
  20. Replies
    5
    Views
    1,299

    FS: Yes, I stand corrected. Cord, not tread.

    Yes, I stand corrected. Cord, not tread.
  21. Replies
    5
    Views
    1,299

    FS: Alaskan Bush Wheels 31's

    One of 31's for sale. Second Generation, one tire has a small area (one inch x one inch where cord started to show, exposed area coated with Rhino Bed liner, all in all coat these with something and...
  22. Replies
    24
    Views
    3,511

    Steve, Sent you a PM Jeff

    Steve,

    Sent you a PM

    Jeff
  23. Replies
    6
    Views
    1,118

    FS: Do you still have this.What does it sell for new?...

    Do you still have this.What does it sell for new?

    jeff
  24. Stewart Hangar 21 Hydrasorb Bungee tool wanted to borrow West Central Florida

    Want to install new sorbs on my Super Cub and would like to borrow the Hangar 21 tool. Anyone willing to loan out there tool? Thanks.

    Jeff Jones
    Jajones@ij.net
  25. Replies
    1
    Views
    832

    MT Constant Speed real cruise numbers

    Considering the MT CS for a 160 hp Super cub and wondered what owners are experiencing for cruise numbers at 24 squared, 25 squared, 26 over 24? Or any power settings. 2 blade vs 3 blade,...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4