Search:

Type: Posts; User: Larry G

Page 1 of 11 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    346
    Views
    44,113

    I get the lenses for my welding helmet then I...

    I get the lenses for my welding helmet then I don't have to where glasses
  2. Replies
    533
    Views
    175,986

    I was thinking the same thing on my seat Mike...

    I was thinking the same thing on my seat Mike that is my YouTube video
  3. Replies
    61
    Views
    10,479

    39682 Not the best picture for you but you can...

    39682
    Not the best picture for you but you can see on top off the boot cowl where there is clecos in pairs holding that part for holding the instrument panel then one screw through the panel
  4. Replies
    71
    Views
    12,542

    I don't believe this one bit, Jay would not say...

    I don't believe this one bit, Jay would not say that. " I know of another that was sent the wrong parts and Jay is saying itís not his problem" Fake News Todd Long
  5. Replies
    1
    Views
    3,374

    Bad day for float plane

    After a rough landing on Lake Tomahawk Friday morning, a float plane, piloted by Betsy Goldbach, was removed from the water that evening by Kozey Crane Service. For the full story, see Tuesday's...
  6. Replies
    19
    Views
    9,790

    29588295892959029591 I finished my engine mount...

    29588295892959029591
    I finished my engine mount and built stands for my wings. Every thing fit nice on the firewall and engine.
  7. Replies
    43
    Views
    16,098

    29342 I seen this picture somewhere else never...

    29342
    I seen this picture somewhere else never seen a cotter pin done that way before. What is the proper way
  8. Replies
    6
    Views
    2,059

    I think the original cub round tip looks much...

    I think the original cub round tip looks much better. Sure I know the other has more lift just my
    preference. Round tip is lighter also.
  9. Replies
    6
    Views
    2,059

    That is the one that I need to make work out.

    That is the one that I need to make work out.
  10. Replies
    6
    Views
    2,059

    Aileron tip bow install

    2924929250
    The aileron tip bow is smaller than the rib on the end of the aileron not sure how to make this work out. Any ideas on how you are supposed to do this would be nice. Or pictures would be...
  11. Replies
    3
    Views
    1,208

    28631

    28631
  12. Thread: My PA-11

    by Larry G
    Replies
    16
    Views
    3,341

    Very nice someone did a beautiful job of painting

    Very nice someone did a beautiful job of painting
  13. Replies
    18
    Views
    5,331

    As long as you said we could ask away. In my...

    As long as you said we could ask away. In my posting of a non-electric experimental plane I would like to know the proper way to wire the starter and switch that I need for that without the...
  14. Replies
    48
    Views
    10,831

    I will definitely keep that in mind Skywagon. Is...

    I will definitely keep that in mind Skywagon. Is there a way to hook it up to have a direct reading and be able to go to the EIS also
  15. Replies
    48
    Views
    10,831

    I was thinking of going with the GRT sport ex...

    I was thinking of going with the GRT sport ex that draws only .5 amps and only weighs 1 1/2 lbs and the EIS to go with it draws only .20 amps. Having a starter would be nice if you have a good...
  16. Replies
    48
    Views
    10,831

    Thanks skywagon8a that is just what I wanted to...

    Thanks skywagon8a that is just what I wanted to know.
  17. Replies
    48
    Views
    10,831

    Frank No hot rod just a O290 D2 the fuse is...

    Frank
    No hot rod just a O290 D2 the fuse is complete so no mods there
  18. Replies
    17
    Views
    10,097

    Randy try Jay at Javeron you must only about 1...

    Randy try Jay at Javeron you must only about 1 1/2 hours or so away
  19. Replies
    48
    Views
    10,831

    Thinking non-electric for exp pa-18 project

    I have been thinking of finishing my exp PA-18 a non electric system with out the starter and alternator and the other goodies that go along with them. To make this project as light as possible. To...
  20. Replies
    255
    Views
    71,894

    Hi Marty looking really good. How is the ...

    Hi Marty looking really good. How is the durability of the paint you used holding up as you assemble.
  21. Replies
    8
    Views
    2,099

    Hope that's not a personal problem also hehehaha

    Hope that's not a personal problem also hehehaha
  22. Replies
    50
    Views
    13,205

    I pick up up some used cabinets from work had one...

    I pick up up some used cabinets from work had one on all the double doors for locking. I'm down to about 10 or so now. Ya at $10.00 a pop that's good profit
  23. Replies
    50
    Views
    13,205

    Ace hardware $2.99 elbow catch...

    Ace hardware $2.99 elbow catch
    http://www.acehardware.com/product/index.jsp?productId=1293787
  24. Replies
    47
    Views
    9,805

    27303 Not sure if this will help you or not this...

    27303
    Not sure if this will help you or not this is from Bill Rusk's photos. This is how Javron does there seams and end ribs.
  25. Thread: PA-18-95 Plans

    by Larry G
    Replies
    24
    Views
    4,127

    Look at this building blog lots of good stuff on...

    Look at this building blog lots of good stuff on how he built his.
    http://www.supercub.org/forum/showthread.php?44825-New-member-building-a-PA18-95
Results 1 to 25 of 272
Page 1 of 11 1 2 3 4