Search:

Type: Posts; User: mike mcs repair

Page 1 of 20 1 2 3 4

Search: Search took 0.09 seconds.

  1. Replies
    2
    Views
    48

    Just follow the instructions as best you can....

    Just follow the instructions as best you can. Might not be able to satisfy them all


    Sent from my iPhone using SuperCub.Org
  2. Replies
    4
    Views
    473

    the hole is higher or lower on rear spars from...

    the hole is higher or lower on rear spars from Univair... or piper messed up...

    even had one i measured that was replaced in 1976 with a univair that was off.....

    you can lay a strait edge on...
  3. Consultation rate is triple shop rate. And this...

    Consultation rate is triple shop rate. And this should be at double that. Ask for mechanics credit card number for your time.


    Sent from my iPhone using SuperCub.Org mobile app
  4. Replies
    4
    Views
    473

    now the question, are the attach holes(at...

    now the question, are the attach holes(at fuselage) at the proper height on rear spars, or off like Univairs???(or was piper not same as it drawing)
  5. Thread: Draco

    by mike mcs repair
    Replies
    61
    Views
    2,434

    I may be wrong... but none of his videos are ad...

  6. Thread: Draco

    by mike mcs repair
    Replies
    61
    Views
    2,434

    Oops, darn it... ...

  7. Replies
    1,249
    Views
    321,303

    I bet he's already looking for a donor.... ...

    I bet he's already looking for a donor....

    plenty of good parts left....
  8. Replies
    1,249
    Views
    321,303

    https://www.youtube.com/watch?v=NfctWAoDXvs

    https://www.youtube.com/watch?v=NfctWAoDXvs
  9. Replies
    1,249
    Views
    321,303

    https://www.youtube.com/watch?v=TtDL3jv4gEQ

    https://www.youtube.com/watch?v=TtDL3jv4gEQ
  10. Replies
    5
    Views
    139

    PA 12 wheel gear wanted

    Does it still have normal-12 gear setup or has it been converted to -18 gear(you can tell if it has cabane V mounting ears added to front gear fittings)


    Sent from my iPhone using SuperCub.Org
  11. Replies
    3
    Views
    284

    Won’t show on normal compression check. Rings are...

    Won’t show on normal compression check. Rings are above crack. The various ADs have yo do a soppy water check with piston BDC if I recall correctly. Thanks for sharing


    Sent from my iPhone...
  12. the bushing are on my inspection sheet as an...

    the bushing are on my inspection sheet as an item, you will wear the bottom ones out first & quite quickly...
  13. Replies
    51
    Views
    7,763

    and that's why I only use vinyl for NNumbers (and...

    and that's why I only use vinyl for NNumbers (and I've had a few on different airplanes that I had to replace after only a few years...)

    the failure mode is they curl up from the edges... I will...
  14. this is also the only way I have seen it done.......

    this is also the only way I have seen it done.... never seen that one bolt into the truss.....
  15. Replies
    3
    Views
    263

    Pictures. No 2 -12 are the same Sent from...

    Pictures. No 2 -12 are the same


    Sent from my iPhone using SuperCub.Org
  16. bump.... any more thoughts on this issue... or is...

    bump.... any more thoughts on this issue... or is it a dead/bad idea?
  17. Replies
    15
    Views
    368

    atlee has new tooling now, no more fluted edges ...

    atlee has new tooling now, no more fluted edges nice and smooth lips
  18. Replies
    15
    Views
    368

    http://www.fadodge.com is where I get my...

    http://www.fadodge.com is where I get my firewalls... he will make them out of stainless or titanium they have a nice lip formed on them

    https://photos.app.goo.gl/oiBAbRz69vR1eM4i9
    ...
  19. Replies
    131
    Views
    27,987

    Start fan on high an hour before painting, the...

    Start fan on high an hour before painting, the turn fan down during painting(moves dust before you paint). Fast fan should have moved the dust. Also hang parts vertically or top DOWN(good side)

    ...
  20. Replies
    10
    Views
    495

    Cessna Pilots Seat.

    http://everyspec.com/MIL-STD/MIL-STD-1700-1799/download.php?spec=MIL-STD-1755.020900.PDF


    Sent from my iPhone using SuperCub.Org mobile app
  21. https://goo.gl/photos/PuiR5ha2aBDbkUBS8 ...

    https://goo.gl/photos/PuiR5ha2aBDbkUBS8

    https://goo.gl/photos/GRXyyNHPoUik2V44A

    You may need to move throttle handle some. And mod rod between handles


    Sent from my iPhone using SuperCub.Org
  22. Replies
    6
    Views
    640

    your plane is an OLD CAR 3 or CAR 03 certified...

    your plane is an OLD CAR 3 or CAR 03 certified plane...

    search for it... should meet the tire requirements... it was very broad
  23. Replies
    1,249
    Views
    321,303

    sure don't see much fuel spilled there..... or...

    sure don't see much fuel spilled there..... or fire.....
  24. Replies
    1,249
    Views
    321,303

    2 times a few summers ago, i watch 2 planes...

    2 times a few summers ago, i watch 2 planes engines quit after/on takeoff, one successfully got it going again.... other was fatal as he tried to turn back and stalled.... I walk by that spot where...
  25. Replies
    93
    Views
    11,444

    I've seen noise/fixed from: loose screw on...

    I've seen noise/fixed from:

    loose screw on output breaker(would sometimes weld, other time be loose and noisy)
    bad grond alt to airframe
    bad master solenoid, burnt contractor?


    (not sure...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4