Search:

Type: Posts; User: adamgrenda

Page 1 of 4 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    1
    Views
    193

    Found some no longer need

    Found some no longer need
  2. Replies
    1
    Views
    193

    WTB Novak Ski Brakes

    Looking for a set of Novak ski brakes for an experimental cub. Let me know what you have please.

    Adam
    907-764-8091
  3. Replies
    175
    Views
    26,198

    I would call Tony I think he has new and updated...

    I would call Tony I think he has new and updated seals. Iíve had a loss of maybe 10-15 psi per side that I add some when I go from wheels to skis. I have to add more pressure for skis and winter...
  4. Replies
    8
    Views
    867

    yea. Itís the bay that only has one reinforcement...

    yea. Itís the bay that only has one reinforcement there. I got a bore scope to stick in there and see exactly what it is and where itís loose. Flying for work has me pretty busy at the moment.
  5. Replies
    8
    Views
    867

    not sure where the parts came from itís a...

    not sure where the parts came from itís a experimental cub but lots of stock parts. Itís small like a welding rod and itís in the same location as the brace that airframes horizontal has
  6. Replies
    8
    Views
    867

    Horizontal has loose wire?

    Fixing one thing and found more broken parts. The horizontal has a internal brace wire that is loose. Itís still connected on both ends but definitely rattling around. Trying to post video
  7. Replies
    10
    Views
    971

    How to replace rear liner tube?

    Done my research on here and the rear liner tube and it looks fairly straightforward. I have about 3/8Ē of liner tube showing on the right side rear tube where it connects the stab to fuse. I think...
  8. Ok great advice thanks Iíll give it a go.

    Ok great advice thanks Iíll give it a go.
  9. Yup did that and still didnít think it would come...

    Yup did that and still didnít think it would come out. Would try again. So castle nut off and then the washers, pulley and then the woodruff key after all this the thick washer comes off so I can add...
  10. I just tried that but couldn’t get the large...

    I just tried that but couldn’t get the large thick washer off so couldn’t add a shim to the bottom of the screw it was almost fixed in place. Don’t have any pics.
  11. EH I’ll take my chances. Living on the edge.

    EH I’ll take my chances. Living on the edge.
  12. Yup good to know. Will order and change this...

    Yup good to know. Will order and change this winter when itís nasty. Itís time to bear hunt now. Tried to shim the bottom just now but to get the shim washer at the bottom of the threads it was...
  13. How to fix this play in jackscrew...video attached

    Found some play in my jackscrew assembly. The nut on the bottom is tight. I put a wrench on it and its real snug. The play seems to be in the jackscrew and the first washer below the threads where it...
  14. Replies
    3
    Views
    547

    great thanks Steve. Sounds easy enough Iíll get...

    great thanks Steve. Sounds easy enough Iíll get one ordered.
  15. Replies
    3
    Views
    547

    Rear stab side to side play

    Researched and only found one thread and still curious how to fix. Only the right side rear stab has about 1/4-3/8Ē of play side to side. I can get it to move only when I lift up on the far edge of...
  16. Replies
    19
    Views
    1,628

    55407 The pads had a slight glaze to them so...

    55407


    The pads had a slight glaze to them so I cleaned them with sandpaper and brake clean. Rotors look good cleaned it with scotchbrite and brake clean. The piston on the caliper had some...
  17. Replies
    19
    Views
    1,628

    Thanks Brian. I’ve bled that way and got all air...

    Thanks Brian. I’ve bled that way and got all air out. What is the best way to start over so to speak and get all fluid out? Open the bleeder on the bottom and had the kid pump the brakes but still...
  18. Replies
    19
    Views
    1,628

    Yup makes sense. I tried that with my NR and...

    Yup makes sense. I tried that with my NR and worked well. I had a hard time getting every last air bubble out of the Steveís brakes so I left them on this year. Iíll let you know how today turns out....
  19. Replies
    19
    Views
    1,628

    yup Iíll try all that today too. What is the...

    yup Iíll try all that today too. What is the usual culprit of a contaminated pad? I donít remember getting those dirty but between grease and swapping skis and wheels it very easily could of got some...
  20. Replies
    19
    Views
    1,628

    I’ve cleaned and checked and lubed the pins when...

    I’ve cleaned and checked and lubed the pins when I put the wheels back on. I’ll pull the caliper off and clean the pads and rotors w brake clean and check the pins again.
  21. Replies
    19
    Views
    1,628

    Pedal is hard and not much travel but no stopping...

    Pedal is hard and not much travel but no stopping power. If contained pad or rotor whatís the remedy to fix?
  22. Replies
    19
    Views
    1,628

    Need help with bleeding Steveís brakes

    Pa-18 on 35s with Steveís brakes.

    200í landings and keeping the tail up with the brakes was not an issue. Left calipers on and went to skis and never cracked a brake line. Went back to wheels and...
  23. Replies
    16
    Views
    7,400

    called and order thanks a bunch.

    called and order thanks a bunch.
  24. Replies
    16
    Views
    7,400

    Anyone have a recent source of getting one of...

    Anyone have a recent source of getting one of these links?
  25. Replies
    12
    Views
    1,895

    WTB: Contact Brian Turner at Last Frontier...

    Contact Brian Turner at Last Frontier Contracting. Custom home builder and a good cub pilot as well
Results 1 to 25 of 93
Page 1 of 4 1 2 3 4