Search:

Type: Posts; User: BC12D-4-85

Page 1 of 20 1 2 3 4

Search: Search took 0.09 seconds.

  1. FWIW Marvel's 1/2 -3/4 turn out in winter-back in...

    FWIW Marvel's 1/2 -3/4 turn out in winter-back in summer for +50 rpm at cutoff.

    Gary
  2. Replies
    35
    Views
    1,394

    A shot glass full in 5 gallons seems to work ok ...

    A shot glass full in 5 gallons seems to work ok

    Gary
  3. Replies
    11
    Views
    762

    There's nothing like taking a full summersault...

    There's nothing like taking a full summersault off a Beaver's wing then sucking in a thousand mosquitoes following.

    Gary
  4. Replies
    18
    Views
    863

    Or sudden prop kickback on starting? Don't open...

    Or sudden prop kickback on starting? Don't open the throttle too much and have the timing checked for too far advanced.

    Gary
  5. Replies
    37
    Views
    1,823

    FWIW you are not alone in having a bad experience...

    FWIW you are not alone in having a bad experience at Tok. Others have both before and since. Some's due to the runway crown, others from the raised runway edge in spots and the typical crosswind...
  6. Replies
    46
    Views
    3,214

    +++ on the inflight mag check. Also try applying...

    +++ on the inflight mag check. Also try applying carb heat when it stumbles - if the then richer mixture helps it might indicate if it's going lean. If it gets worse with carb heat it may be going...
  7. Replies
    982
    Views
    202,337

    Land into any wind on ice. Tires will give some...

    Land into any wind on ice. Tires will give some sideways but a ski skeg can grab a hard rough spot and try to twist the gear even going straight ahead.

    GAry
  8. Replies
    36
    Views
    1,715

    See this...see this with A&P attached...see them...

    See this...see this with A&P attached...see them smile and file away your prop. Then ask why it no longer performs like new. Secret: Keep from dinging up your prop with rocks, ice, and water.
    ...
  9. Replies
    36
    Views
    1,715

    These long thin props get reworked as wear...

    These long thin props get reworked as wear occurs. Eventually they reach minimum standards for size and shape - length, width, thickness, and airfoil. Not saying yours is worn out but they can get...
  10. Replies
    389
    Views
    75,734

    Best wishes for strength RV and a better New...

    Best wishes for strength RV and a better New Year.

    Gary
  11. Replies
    122
    Views
    29,241

    What's a typical drop test on floats involve? I...

    What's a typical drop test on floats involve? I read CAR3 and it lists some +% safety criteria (like +1.5-1.85) but missed the actual method of conformity.

    Gary
  12. Try some static rpm runs, climb performance, and...

    Try some static rpm runs, climb performance, and cruise with both and let us know the results. Lots of info on either prop but rarely on the same engine. Nice Cub!

    Gary
  13. Replies
    11
    Views
    710

    Some environmental stains can be removed with...

    Some environmental stains can be removed with solvent > I've had some success using charcoal lighter fluid which doesn't seem to attack the Poly Tone. I had a PA-11 painted yellow that literally ate...
  14. Replies
    33
    Views
    1,692

    Any PA-11 much over 800# is fat....ok I'll say...

    Any PA-11 much over 800# is fat....ok I'll say 850 to be nice. I tried to ruin one by adding extended flaps (+20#) and a PA-18 tail (way heavier than stock), and succeeded in getting it close to...
  15. Replies
    58
    Views
    3,582

    Go Back to the Future for the next big thing:...

    Go Back to the Future for the next big thing: https://www.supercub.org/forum/showthread.php?35321-GURNEY-FLAPS-WICKERBILLS-testing-data-and-photos

    Gary
  16. Replies
    58
    Views
    3,582

    Overall it's probably is best to design like the...

    Overall it's probably is best to design like the PStol with an intermediate 'flap' between the wing and any lower element. Gradually direct the air to bend down and follow the flap's contour via any...
  17. Replies
    58
    Views
    3,582

    I wonder what would happen if they sealed the...

    I wonder what would happen if they sealed the normal cove gap between the LE of the flap and wing? Force the air under the wing to mainly flow through the flap's LE slots. Some sort of sliding...
  18. Replies
    2,071
    Views
    521,458

    Part of earning the Rating is wearing a...

    Part of earning the Rating is wearing a parachute.

    Gary
  19. Replies
    2,071
    Views
    521,458

    A new Rating required? Gary

    A new Rating required?

    Gary
  20. Replies
    19
    Views
    1,145

    Trim wheel rolled pins....first time they sheared...

    Trim wheel rolled pins....first time they sheared or fell out I was near Alaska's Pt. Barrow (now Utqiagvik) on floats. Hauling some loads and lots of T/O's into small lakes. I needed them but none...
  21. My Taylorcraft performs exactly as Dan's does on...

    My Taylorcraft performs exactly as Dan's does on floats - C-85 Stroker and same prop dragging EDO 1320's at 2350-2400. My experience with props also dupes N1PA's. I ended up with an 8042 with the...
  22. Replies
    7
    Views
    626

    If the pipe that slides into another is too small...

    If the pipe that slides into another is too small and loose or deformed> enlarge or at least make it round again it with a common exhaust pipe expander tool. They are available at most auto parts...
  23. Replies
    51
    Views
    3,091

    Go look at the front of a Cessna cowl intake for...

    Go look at the front of a Cessna cowl intake for a similar sized engine. They tend to do baffling well likely for a reason.

    Gary
  24. Replies
    51
    Views
    3,091

    Here's an interesting comment on straightening...

    Here's an interesting comment on straightening air flow through the carb and affecting mixture distribution:

    https://www.shortwingpipers.org/forum/showthread.php?5018-Carburetor-heat-box&

    Gary
  25. Replies
    20
    Views
    1,109

    Maybe put a big magnet nearby? Mine had it done...

    Maybe put a big magnet nearby? Mine had it done but not sure if its steel or other.

    Edit: Steel> https://bandc.com/wp-content/uploads/2018/05/fk501_3_revE.pdf

    Gary
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4