Search:

Type: Posts; User: sdischer

Page 1 of 6 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    1,187
    Views
    277,649

    55046 55047 Brazos River. I named this one...

    55046

    55047
    Brazos River. I named this one "Gravel Bar" because I am creative like that.
  2. Replies
    40
    Views
    2,317

    Mine is on the metal battery hatch behind the...

    Mine is on the metal battery hatch behind the passenger (turtledeck).
  3. I think I agree with you. I am not sure that the...

    I think I agree with you. I am not sure that the extra hassle and money is worth it for saving 10 more pounds. I think this is really the best of both worlds and maybe a few less tacos per day and I...
  4. Thanks. Experiences like this are very valuable....

    Thanks. Experiences like this are very valuable. Leaving the battery where it is is also 10x easier for me!
  5. Good point! Sent from my iPhone using...

    Good point!


    Sent from my iPhone using Tapatalk
  6. Earthx ETX900-TSO + FAtlee Dodge Battery Box in a PA-18-95

    I already have a B&C generator and starter and I now am ready to lose 25 pounds (and several hundred $) from behind the back seat by dumping the old 30# battery.

    1. Has anyone been successful...
  7. Replies
    7
    Views
    954

    SOLUTION: I have a saying, every problem is the...

    SOLUTION: I have a saying, every problem is the result of a previous solution and this time it is no different. I raised my breather tube up a couple of inches a while back to get it out of the...
  8. Replies
    75
    Views
    11,853

    Reopening this thread ( and hopefully not a can...

    Reopening this thread ( and hopefully not a can of worms) but North River Aviation versus Steve's Brake Boosters, which do you recommend and why? I feel like I am really stressing my Scott...
  9. Replies
    9
    Views
    967

    Steve is this the tool you have? ...

    Steve is this the tool you have? https://www.aircraft-tool.com/shop/detail.aspx?id=4915A&AspxAutoDetectCookieSupport=1
  10. Replies
    9
    Views
    967

    Iím thinking the Real GasketsĒ tubes are the way...

    Iím thinking the Real GasketsĒ tubes are the way to go. I assume you cut off the old tubes and then extract the tube piece left in the head? How difficult? Worse than cutting off a pinion pivot...
  11. Replies
    9
    Views
    967

    Both of these are great ideas!

    Both of these are great ideas!
  12. Replies
    9
    Views
    967

    TCM C90 Push Rod Tube Leakage

    I am getting a little oil seepage where the push rod tubes press into the head/rocker box. I dabbed a little High Temp RTV on the outside all the way around the circumference and the leak has...
  13. Replies
    7
    Views
    954

    Thanks Mike. I will give that a try. All I have...

    Thanks Mike. I will give that a try. All I have to do is crack the heater open and the smell stops. I think you are onto something.
  14. Replies
    7
    Views
    954

    The triangle just above the tail spring on the...

    The triangle just above the tail spring on the bottom of the fuse isnít covered. Iím wondering if that one inch wide by three inch long gap is enough to pull a vacuum?
  15. Replies
    7
    Views
    954

    Seal brake lines

    My brake lines exit through slots in two inspection covers in the floor of my fuselage. I assume this is typical. I get a good bit of exhaust fumes coming in around the brake lines. Anyone have a...
  16. Not sure how you got a hacksaw blade in there!

    Not sure how you got a hacksaw blade in there!
  17. glad I didnít know about exposing a hole! What...

    glad I didnít know about exposing a hole! What is that about, like a pilot hole inside the shaft? Can you hit it if you cut too far back or what?
  18. Yes I already do. It really cleaned up the...

    Yes I already do. It really cleaned up the engine compartment too.
  19. B&C Starter and Generator Installation Experience

    I wanted to make a few notes about my experience installing the B&C generator and starter on my PA-18-95. To prep to cut off the starter pivot shaft, I first used Flex Seal tape. If you haven't...
  20. Replies
    2
    Views
    439

    awesome! Thanks

    awesome! Thanks
  21. Replies
    2
    Views
    439

    66696-00 ammeter Replacement

    Looking for a replacement for my ammeter. That part number 66697-00 seems to be no longer available so would a Stewart Warner ammeter be the best option? Mine has a 40-0-40 in it right now but...
  22. Replies
    51
    Views
    4,870

    Kicking myself I didn't think of that. I might...

    Kicking myself I didn't think of that. I might pull it and hide mine anyway.
  23. Replies
    51
    Views
    4,870

    I feel so ignorant, that is genius! I could have...

    I feel so ignorant, that is genius! I could have saved a lot of trouble.
  24. Replies
    20
    Views
    1,999

    Unfortunately itís Skytec that provides the tray...

    Unfortunately itís Skytec that provides the tray and I bought B&C! My luck...
  25. Replies
    51
    Views
    4,870

    I opened up the hole with a dremel. I was was a...

    I opened up the hole with a dremel. I was was a long and tedious process but it will work. The bulb body barely touches the fabric from the inside. Works great and shouldn't cause fabric issues.
Results 1 to 25 of 128
Page 1 of 6 1 2 3 4