Search:

Type: Posts; User: tempdoug

Page 1 of 20 1 2 3 4

Search: Search took 0.19 seconds.

  1. Thread: tail support

    by tempdoug
    Replies
    3
    Views
    186

    thanks mike!!! i also see some triangle pieces...

    thanks mike!!! i also see some triangle pieces welded to the cross tube supports. ive seen a little different idea there. first thing i thought when i seen this picture is a electric trim motor right...
  2. Thread: tail support

    by tempdoug
    Replies
    3
    Views
    186

    tail support

    anyone have any pictures of the inside of the fuselage using this tail support? just would like to see how it works is all.http://crosswindsstol.com/stc.html
  3. Replies
    24
    Views
    1,166

    https://www.supercub.org/forum/attachment.php?atta...

    https://www.supercub.org/forum/attachment.php?attachmentid=25890&d=1464361260
  4. Replies
    24
    Views
    1,166

    the 2 i seen, wished i would have asked, so i...

    the 2 i seen, wished i would have asked, so i dont know, and a very good point for the lube zerc.
  5. Replies
    51
    Views
    13,607

    https://www.aircraftspruce.com/catalog/eppages/dl2...

    https://www.aircraftspruce.com/catalog/eppages/dl20.php?clickkey=59213
  6. Replies
    24
    Views
    1,166

    1/4-28-grease zerc. i think.

    1/4-28-grease zerc. i think.
  7. Replies
    30
    Views
    1,269

    TV tells us were in good times.

    TV tells us were in good times.
  8. Replies
    30
    Views
    1,269

    https://www.madcustomcubs.com/blank-page

    https://www.madcustomcubs.com/blank-page
  9. Replies
    30
    Views
    1,269

    https://scontent.fbis1-1.fna.fbcdn.net/v/t1.0-9/82...

    https://scontent.fbis1-1.fna.fbcdn.net/v/t1.0-9/82561790_10221019680703194_569338670029471744_n.jpg?_nc_cat=102&_nc_ohc=iAEXcOQE8xcAX-GDxZw&_nc_ht=scontent.fbis1-1.fna&oh=064497533e4e608bd012edfb4178c...
  10. Replies
    34
    Views
    1,610

    i was thinking of trying keyed rivnuts with a...

    i was thinking of trying keyed rivnuts with a nylon washer under the screw head.
  11. Replies
    34
    Views
    1,610

    steve, can you fold up that bottom door and take...

    steve, can you fold up that bottom door and take a picture, would like to see how the plexi is fastened. if you have access to it.
  12. Replies
    51
    Views
    3,431

    i set the trim for 45-50 at 1000-1100 rpm to fly...

    i set the trim for 45-50 at 1000-1100 rpm to fly hands off and never touch it again, just use power and elevator after that.
  13. Thread: Hanger Heat

    by tempdoug
    Replies
    29
    Views
    1,334

    one of these heats my garage floor. put in 16...

    one of these heats my garage floor. put in 16 years ago, so far perfect, havent touched a thing. got the thermostat at 55 and it sits there year...
  14. Thread: Hanger Heat

    by tempdoug
    Replies
    29
    Views
    1,334

    one thing, copper carries electricity. and these...

    one thing, copper carries electricity. and these new generation heaters without the pilot light they use a spark plug to start and have power fan venting where you can go out instead of up, so you...
  15. Thread: Hanger Heat

    by tempdoug
    Replies
    29
    Views
    1,334

    theres thousands of miles of copper line still...

    theres thousands of miles of copper line still doing the job, but some of the propane truck drivers are getting touchy. and i only have 2 options for a supplier.
  16. Thread: Hanger Heat

    by tempdoug
    Replies
    29
    Views
    1,334

    i went with a mr heater but only been in a week...

    i went with a mr heater but only been in a week from northern tool. so havent come up with a opinion yet. these are fan heaters. radiant heaters are another deal, know nothing about them. just giving...
  17. Thread: Hanger Heat

    by tempdoug
    Replies
    29
    Views
    1,334

    just redid my loader tractor shed. found a 50...

    just redid my loader tractor shed. found a 50 chunk of this for 100 bucks. but to buy it, its spendy. unless menards or someplace would have it cheaper, very nice to work...
  18. Thread: Hanger Heat

    by tempdoug
    Replies
    29
    Views
    1,334

    stuart our propane places are using this outside...

    stuart our propane places are using this outside below ground...
  19. Thread: Hanger Heat

    by tempdoug
    Replies
    29
    Views
    1,334

    propane line above or below ground outside or do...

    propane line above or below ground outside or do you mean inside?
  20. Replies
    7
    Views
    384

    it actually would be nice to find a flat print of...

    it actually would be nice to find a flat print of that. anyone want to take one and hammer it flat and trace around it? only problem it would make it to easy. except for the bending.
  21. Replies
    33
    Views
    1,838

    if you build your frame thats also going to take...

    if you build your frame thats also going to take some time, depends on your talent. and time for project. and cash. and also wanted to add, think about the wider frame, interested how much more...
  22. Replies
    33
    Views
    1,838

    get a wing kit from jay. and put it together...

    get a wing kit from jay. and put it together yourself.
  23. Replies
    43
    Views
    2,825

    baits. Small slices of hot dog (cooked or...

    baits.


    Small slices of hot dog (cooked or uncooked)
    A dollop of maple syrup (mice have a sweet tooth)
    Bacon bits that you have cooked up yourself or even raw – not the ones from a jar or...
  24. Replies
    4
    Views
    318

    elevator or stab? if im following you?

    elevator or stab? if im following you?
  25. Replies
    27
    Views
    1,401

    glenn, the pa11 mount is about ainch or inch and...

    glenn, the pa11 mount is about ainch or inch and a half back from the 90 supercub mount right?
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4