Search:

Type: Posts; User: TEVogt

Search: Search took 0.01 seconds.

  1. Replies
    20
    Views
    4,356

    The Tarvers (father & son) are rebuilding hubs...

    The Tarvers (father & son) are rebuilding hubs and manufacturing props, but at this time only for the experimental market. Apparently they got into a disagreement with the FAA, and neither group is...
  2. Replies
    20
    Views
    4,356

    Thanks for checking Glen! Could you check to see...

    Thanks for checking Glen! Could you check to see if there are any references to the spinner they made for Swifts...S-1B Spinner Assembly.

    Previously I had a MCCAULEY 1C90LM7246 prop that is/was a...
  3. Replies
    20
    Views
    4,356

    Thanks for the information...... that's certainly...

    Thanks for the information...... that's certainly helpful about the prop, but is there any further information about the spinners that were designed for the aeromatic?
  4. Replies
    20
    Views
    4,356

    So far I haven't been able to locate the part...

    So far I haven't been able to locate the part numbers, but I don't give up easily. I do have the Swift Museum and other leads through them looking for me too. To bad Univair wasn't been able to give...
  5. Replies
    20
    Views
    4,356

    One other thing I need to find out.... Does any...

    One other thing I need to find out.... Does any one happen to know or know where I could find the component part numbers or drawings to the S-1B spinner assembly. There are 3 main parts 1) the front...
  6. Replies
    20
    Views
    4,356

    Well I'm happy to say I was able to hang a...

    Well I'm happy to say I was able to hang a spinner on my Aeromatic prop last weekend. It took some research and scrounging but what I did was to buy a good used S-1B swift spinner and a new...
  7. Replies
    2
    Views
    1,026

    AeroMatic and Manifold Gauge

    I'm installing a newly overhauled Tarver Aeromatic F200/00-73E in front of my PA12 0234C1 in the next 2 weeks. Home is a grass strip in the Midwest and I fly below 5,000 ft. I have some time behind...
  8. Replies
    20
    Views
    4,356

    Yeah I see what you're saying. Yesterday I called...

    Yeah I see what you're saying. Yesterday I called aircraft Spruce and they pulled a BN-1 bullet nose spinner from inventory, and measured from the base to where it started to taper and that was...
  9. Replies
    20
    Views
    4,356

    I found a spinner that might work. My...

    I found a spinner that might work. My understanding is that the aeromatic has a 8 x 8 cylinder space that the spinner would have to cover. ACS makes a spinner called BN–1 bullet nose spinner. The...
  10. Replies
    20
    Views
    4,356

    Hi Sam, I'll let you know what I come up with....

    Hi Sam,
    I'll let you know what I come up with. I'd like to talk to you about the aromatic when you have a moment.
  11. Replies
    20
    Views
    4,356

    Spinner for a Aeromatic Propeller

    Do any of you fellow flyers know a model number or have experience with spinner setup for a PA12 with a 0235C1 and aeromatic F200 propeller. I've talked with Kent but I'm having some difficulties...
  12. Replies
    21
    Views
    7,485

    I owned my 12 for 30 years and no problems with...

    I owned my 12 for 30 years and no problems with tank covers.....and then pop. Almost all screws were still attached including hinge screws. I had that side tank replaced at the annual 4 months...
Results 1 to 12 of 23