Search:

Type: Posts; User: skywagon8a

Page 1 of 20 1 2 3 4

Search: Search took 0.08 seconds.

  1. Replies
    10
    Views
    172

    Don't all sales mangers say the same thing about...

    Don't all sales mangers say the same thing about their automotive products?
  2. Replies
    10
    Views
    172

    http://motorcitymusclecars.files.wordpress.com/201...

    http://motorcitymusclecars.files.wordpress.com/2010/07/jeep-in-a-crate.jpg
  3. Replies
    1,211
    Views
    314,353

    Rangeley Lake is 1500 feet above sea level. I...

    Rangeley Lake is 1500 feet above sea level. I know that is not high to you western folks but, it does mean about 1-1/2" manifold pressure reduction from sea level which does make a difference.

    I...
  4. Replies
    237
    Views
    89,809

    Perhaps it's just not visible in the pictures?...

    Perhaps it's just not visible in the pictures? Where are the holes to bolt on the rear spar to fuselage fitting?
  5. Thread: CAS vs IAS

    by skywagon8a
    Replies
    22
    Views
    622

    Geeeze jsbc, you are to be commended for your due...

    Geeeze jsbc, you are to be commended for your due diligence, however it is only a Cub. Cover the instrument panel so that you can't see any instruments and learn to fly the airplane by looking at the...
  6. Replies
    1,211
    Views
    314,353

    He spotted an obstacle in the water at the last...

    He spotted an obstacle in the water at the last instant and had to make a quick turn to avoid it. :evil:
  7. For you experimental guys, here is a very good...

    For you experimental guys, here is a very good solution. It is a Kubota tractor dynamo and regulator. Total installed weight 5 pounds. The output is just over 15 amps. It is shown on a float plane...
  8. Replies
    19
    Views
    811

    Sand enough so that there are no scratches. A...

    Sand enough so that there are no scratches. A small scratch where there is a bending load can cause it to crack and break. Just like a small nick in an aluminum propeller can cause a blade to break...
  9. Replies
    20
    Views
    917

    Ron, While I can't vouch for the performance...

    Ron,
    While I can't vouch for the performance with only 108 hp, a wet grass attempt isn't out of the question. You certainly will not get tangled up with the trailer poking a hole in your floats in...
  10. Replies
    19
    Views
    811

    If you are anywhere near Boston I can give you...

    If you are anywhere near Boston I can give you the name of a good source in Dorchester.
  11. Replies
    29
    Views
    4,366

    The reason I asked about the different power is...

    The reason I asked about the different power is this picture. One looks considerably larger than the other. You certainly have provided a good reason to have two engines, particularly where you are...
  12. Replies
    29
    Views
    4,366

    Just curious, did you previously have a prop...

    Just curious, did you previously have a prop strike with that prop? I'm wondering why it chose to fail.
    Also you have two different sized outboards. What process do you use to balance them for...
  13. Replies
    20
    Views
    917

    Hi ron, How rough is your grass runway? One...

    Hi ron, How rough is your grass runway? One person's rough may be anything rougher than a golfing green. Is it just a little bumpy or does it have rolling hills?? When you have the plane on a trailer...
  14. Replies
    127
    Views
    22,900

    The important thing to consider is to whether...

    The important thing to consider is to whether there can be some blockage trapping air in the cooler which would effectively reduce the available cooling capacity. It's best to place the inlet at the...
  15. Replies
    127
    Views
    22,900

    Denny, I read his post as meaning the oil...

    Denny, I read his post as meaning the oil temperature started down when the rpm dropped below 2100 and that the CHTs did not exceed 370-390 at all power settings.
  16. Replies
    1,211
    Views
    314,353

    A misleading headline when the plane was made in...

    A misleading headline when the plane was made in Slovenia.
  17. Replies
    7
    Views
    1,181

    FS: SOLD and gone to it's new home. It will reappear,...

    SOLD and gone to it's new home. It will reappear, as it's new New England owner is well known by all here.
  18. Replies
    26
    Views
    870

    You could just hard mount a large tablet on the...

    You could just hard mount a large tablet on the panel and go flying. Easy when you are starting from scratch with nothing.
  19. Replies
    20
    Views
    1,705

    Yup, It is a wonder that all who have sat through...

    Yup, It is a wonder that all who have sat through a talk by the FAA's legal department at an IA meeting haven't just turned in their IA tickets on the table and walked out.
  20. Replies
    26
    Views
    870

    Interesting device. Notice Bertarelli promoting...

    Interesting device. Notice Bertarelli promoting that there are no wires and other devices on the glare shield all while he is riding as a passenger in a Bonanza with a device in his lap. Where does...
  21. Replies
    127
    Views
    22,900

    I disagree Denny, with an ambient temperature of...

    I disagree Denny, with an ambient temperature of 100*, CHTs 370-380* is good cooling.

    A 4" hose giving more volume of air through the cooler may help. And the seaplane lip is also a good...
  22. Replies
    17
    Views
    1,182

    With the spacer??

    With the spacer??
  23. Replies
    17
    Views
    1,182

    For what it's worth, I have heard that the reason...

    For what it's worth, I have heard that the reason for the two manufacturers having different re-pitching and repairing limits is because they use different alloys of aluminum. They seem to keep this...
  24. Replies
    4
    Views
    192

    I hadn't received any subscribed thread notices...

    I hadn't received any subscribed thread notices in more than a month. Last evening they started coming and seem to be continuing as usual.
  25. Here is another question: How do you replace the...

    Here is another question: How do you replace the cam and lifters without​ doing a bottom end overhaul?
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4