Search:

Type: Posts; User: wireweinie

Page 1 of 20 1 2 3 4

Search: Search took 0.07 seconds.

  1. Replies
    17
    Views
    140

    Double check the model. A GTX 327 can be used...

    Double check the model. A GTX 327 can be used with a UAT to make an ADS-B out unit. Does Flightaware track transponders or only ADS-B signals? I'm assuming both, but . . .

    Go through the system...
  2. Replies
    4
    Views
    126

    Be aware that a door from one aircraft rarely...

    Be aware that a door from one aircraft rarely fits another without some adjustments.

    Web
  3. Replies
    17
    Views
    140

    What equipment do you have installed right now...

    What equipment do you have installed right now besides the GDL 39? Transponder? UAT?

    Web
  4. Replies
    17
    Views
    140

    A GDL 39 unit is for ADS-B in. Web

    A GDL 39 unit is for ADS-B in.

    Web
  5. If you store it for a year, take what you've...

    If you store it for a year, take what you've already done, through a one pound bag of desicant on the engine and bag the whole thing tightly. If you want a little extra, vacuum the air out of the bag...
  6. Thread: E-Cub

    by wireweinie
    Replies
    13
    Views
    329

    Another thing to consider with electric vs gas;...

    Another thing to consider with electric vs gas; When you take off with a full load of gas/kerosene you get lighter as you use fuel. A depleted battery weighs the same as a fully charged one.

    Web
  7. Thread: E-Cub

    by wireweinie
    Replies
    13
    Views
    329

    Gasp!?!? LOL. Right now it's pretty much a...

    Gasp!?!?

    LOL. Right now it's pretty much a weight issue. Like Mike pointed out, those batteries weigh a lot. Then look at the weight of a 5 HP electric motor compared to the weight of a 5 HP...
  8. Replies
    13
    Views
    295

    This is a clip from the CGR 30P manual. The stand...

    This is a clip from the CGR 30P manual. The stand alone EGT gauges are identical. These instructions tell you to determine the best location at which ALL probes can be mounted the same distance fron...
  9. Replies
    13
    Views
    295

    No, it's because, inevitably, the holes will...

    No, it's because, inevitably, the holes will shift under heat and pressure and guillotine the probes.

    Web
  10. Replies
    113
    Views
    4,869

    I'm surprised that there are many references to...

    I'm surprised that there are many references to Stitts but only one or two of Ceconite. I'm far from being any kind of expert on fabric, but that means I like simple. With the Ceconite system you...
  11. Replies
    63
    Views
    15,762

    Poll: Does your AFM call out VFR or IFR operation...

    Does your AFM call out VFR or IFR operation limits?

    Web
  12. Replies
    13
    Views
    295

    All installation instructions I've used tell you...

    All installation instructions I've used tell you a range that the probes SHOULD be installed at. But they also tell you that it is more important to keep them all the same distance from the flange....
  13. Replies
    16
    Views
    571

    Only if you have a Denso alternator and of the...

    Only if you have a Denso alternator and of the same model and size as Eddie.

    Asking what the field current would be in 'a 30 amp alternator' is like asking how hard the wind should blow. What...
  14. Replies
    65
    Views
    4,281

    Question: In TIG, if the gas shield is important...

    Question: In TIG, if the gas shield is important to protect the weld from oxygen, why don't welders pipe argon into the tube being welded? Wouldn't the shield be needed on both sides of the weld?
    ...
  15. Thread: New Windows

    by wireweinie
    Replies
    7
    Views
    378

    Do you have the fuzzy insert in the channel? If...

    Do you have the fuzzy insert in the channel? If so, sounds like you'll need to pull the windows and sand any high spots on the top or bottom edges.

    Web
  16. Replies
    16
    Views
    571

    Nope. The reg is trying but the alternator...

    Nope.

    The reg is trying but the alternator can't work until it's turning.

    Web
  17. Replies
    16
    Views
    571

    That is incorrect. With the system powered on but...

    That is incorrect. With the system powered on but the engine not turning, there will be no output from the alternator but there will be current flowing through the field windings. The reason is that...
  18. Replies
    15
    Views
    469

    The 12 amp 200G will work well for you. From the...

    The 12 amp 200G will work well for you. From the list you showed in there's no way you'd need a 30 amp alternator. And the 200G will save you about a pound over the bigger one.

    Web
  19. Replies
    15
    Views
    469

    I don't believe that the gear is modified. It...

    I don't believe that the gear is modified. It just needs to be supplied by the customer.

    Web
  20. Replies
    65
    Views
    4,281

    You engineer types on here, what are the...

    You engineer types on here, what are the technical differences between 1025 and 4130 when it comes to welding and shaping (as in bending or re bending)?

    Web
  21. Replies
    113
    Views
    4,869

    100% agree with dope being forgiving of bad...

    100% agree with dope being forgiving of bad technique. If I can shoot dope and make it look good, anyone can.

    Web
  22. Replies
    16
    Views
    571

    Short circuits get hot. Web

    Short circuits get hot.

    Web
  23. Replies
    16
    Views
    571

    Turn on the master. Note the amp reading. Pull...

    Turn on the master. Note the amp reading. Pull the field breaker and note the amp reading. The difference between the two readings is the total current going through the field. Any reading on the...
  24. Replies
    16
    Views
    571

    How are you observing the current draw? Panel...

    How are you observing the current draw? Panel mounted ammeter? If so is it in the bus feed or is it in the alternator output?

    Web
  25. Replies
    16
    Views
    571

    Lol. To many variables. What brand/model? 14 volt...

    Lol. To many variables. What brand/model? 14 volt or 28 volt? Old or new? 'A' circuit or 'B' circuit? And not sure why you'd want to check current draw when you could just do a voltage check.

    The...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4