Search:

Type: Posts; User: Longwinglover

Page 1 of 20 1 2 3 4

Search: Search took 0.22 seconds.

  1. Replies
    12
    Views
    9,092

    I'm pretty sure it rolled at least 6" -- ...

    I'm pretty sure it rolled at least 6" -- BACKWARDS !!

    John Scott
  2. Thread: Thanks

    by Longwinglover
    Replies
    14
    Views
    4,283

    The Lord even smiles on those that don't have a...

    The Lord even smiles on those that don't have a Cub...

    Beautiful picture ! :up

    John Scott
  3. Replies
    271
    Views
    126,158

    Hmmmm... I thought the bottom was done last so...

    Hmmmm...

    I thought the bottom was done last so when you rip the fabric on a stump you can just soak the tapes and fabric off and replace? I guess things change or don't.

    John Scott
  4. Replies
    43
    Views
    12,826

    Let's see... Is your PA-12 certified or...

    Let's see... Is your PA-12 certified or experimental?

    If certified, is the O-320 install done by STC or otherwise? I'd assume PMA'd parts built to an approved specification/blueprint? ...
  5. Replies
    116
    Views
    59,144

    Thanks for taking the time to reply... John...

    Thanks for taking the time to reply...

    John Scott
  6. Replies
    58
    Views
    27,659

    Pete, In retrospect, I think it was a...

    Pete,

    In retrospect, I think it was a statement and a question you posed that spurred my reply. The rib does actually do more than just give the fabric shape in that it is the structure...
  7. Replies
    58
    Views
    27,659

    I'd tend to disagree in the case of a rib...

    I'd tend to disagree in the case of a rib stitched, Piper rib. The lifting force acts on the upper fabric which is held in place by the rib stitches that transfer the forces to the lower capstrip of...
  8. Replies
    116
    Views
    59,144

    Bob, Bobby, That is one AWSOME "Cub"! ...

    Bob, Bobby,

    That is one AWSOME "Cub"! Visually, the first thing that sets it apart is the landing gear. Can you make a guess as to the difference in weight over a "standard" Cub gear set-up? Is...
  9. Replies
    86
    Views
    40,932

    Well, Bob, if you will follow what Pete posted it...

    Well, Bob, if you will follow what Pete posted it just might go a little faster? Then again it IS the FAA and they're not happy until you're not happy.

    John Scott
  10. Replies
    6
    Views
    2,710

    In my opinion, WagAero's motto should be:...

    In my opinion, WagAero's motto should be: Everything not quite right...

    John Scott
  11. Replies
    58
    Views
    17,903

    Didn't Cessna just grind the "pointer" off the...

    Didn't Cessna just grind the "pointer" off the short end?? LOL !!

    John Scott
  12. Replies
    58
    Views
    14,543

    Sheeesh! And all this time I thought we were...

    Sheeesh! And all this time I thought we were fixing this with phonics!!!

    John Scott
  13. Replies
    2,200
    Views
    1,064,544

    From the pictures, the tail weighing point is...

    From the pictures, the tail weighing point is clearly the tailwheel, not the tailpost.

    John Scott
  14. Replies
    9
    Views
    5,110

    It might be the "next best thing" and I wish them...

    It might be the "next best thing" and I wish them luck in their marketing.

    Can't help but think "Champ gear on a Cub".

    John Scott
  15. Replies
    6
    Views
    501

    It's just like a Majic Cub... John Scott

  16. Replies
    8
    Views
    2,784

    In the attached picture the copper tubing you see...

    In the attached picture the copper tubing you see has been replaced with aluminum tubing. This picture is looking down from the top of the wing, front side of the spar. The nuts are on the jury...
  17. Replies
    2,212
    Views
    487,639

    Hmmmm... Never got much painting done with the...

    Hmmmm...

    Never got much painting done with the compressor off. :wink:

    Since the line is open to the tank, pressure in the line = pressure in the tank. If the compressor runs without you...
  18. Replies
    2,212
    Views
    487,639

    Not fightn' just discussin' If you have a...

    Not fightn' just discussin'

    If you have a compressor with a 100 cubic foot tank filled to 100 PSI.
    You disconnect the air line and installed a gauge in the line outlet. The gauge would read 100...
  19. Replies
    2,212
    Views
    487,639

    Sounds like you need to replace leaky hoses? A...

    Sounds like you need to replace leaky hoses? A longer run technically just increases the volme of higher pressure air - doesn't cause lower pressure.

    Now, if you were painting with electricity,...
  20. Replies
    45
    Views
    12,432

    I am SO glad you posted this! You know the first...

    I am SO glad you posted this! You know the first thing you have to do to complete this mod is to take the front seat out... :lol:


    John Scott
  21. Replies
    81
    Views
    37,161

    I understand global warming has turned things on...

    I understand global warming has turned things on their head in parts of Alaska...

    John Scott
  22. Replies
    37
    Views
    13,455

    I think you mention girls, drinking and gambling...

    I think you mention girls, drinking and gambling to throw us pilots off the scent. We probably have a better chance of getting Victoria to tell us her secrete than finding out the Stewarts guy says...
  23. Replies
    37
    Views
    13,455

    Yeah, but what happens in Vegas, stays in Vegas! ...

    Yeah, but what happens in Vegas, stays in Vegas! Wouldn't be able to share any answers with the crowd. Bummer!

    John Scott
  24. Replies
    66
    Views
    17,783

    :pop: Let's see who admits to flying the short...

    :pop:

    Let's see who admits to flying the short bus...

    John Scott

    All control inputs on the 320/330/340/350/380 are routed through the flight control computer. There is no OFF.
  25. Replies
    36
    Views
    11,227

    Hello, Progressive? Could I speak to Flo? She's...

    Hello, Progressive? Could I speak to Flo? She's not going to believe this...

    John Scott
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4