Search:

Type: Posts; User: KJC

Page 1 of 14 1 2 3 4

Search: Search took 0.13 seconds.

  1. This project is going to depend a lot on what...

    This project is going to depend a lot on what kind of tanks you have. If you have the old ternplate tanks forget about it. If you have any of the newer Dakota, Air Energy or Univair aluminum tanks...
  2. Thread: Seaplane Doors

    by KJC
    Replies
    29
    Views
    4,158

    Stewart s that some kind of wiper seal on that...

    Stewart s that some kind of wiper seal on that door as opposed to bulb seal on the frame?
  3. Thread: Seaplane Doors

    by KJC
    Replies
    29
    Views
    4,158

    Ok. Clear lower door. Like this then. Use #6...

    Ok. Clear lower door. Like this then. Use #6 keyed riv nuts and #6 cad plated machine screws and countersunk washers. You need to weld tabs along the upper edge of the door as shown because the latch...
  4. Thread: Seaplane Doors

    by KJC
    Replies
    29
    Views
    4,158

    Here is a picture of the assembly drawing for the...

    Here is a picture of the assembly drawing for the upper door showing the location of the latch.

    59538
  5. Thread: Seaplane Doors

    by KJC
    Replies
    29
    Views
    4,158

    I’m a little confused on the question still. The...

    I’m a little confused on the question still. The photos above show a PA-12. It has a single piece door held in the up position by a hydraulic actuator like this:


    59534

    I think you are looking...
  6. Thread: Seaplane Doors

    by KJC
    Replies
    29
    Views
    4,158

    Regarding the most current question, is this on...

    Regarding the most current question, is this on an -18?
  7. Replies
    14
    Views
    1,084

    Well this is all I can think of. The part in...

    Well this is all I can think of. The part in question is a section of aluminum compression fitting from a wing complete with AN3 inserts. It looks factory made and fits perfectly between the welded...
  8. Thread: Scott 3200 AN6?

    by KJC
    Replies
    11
    Views
    763

    Yeah I don’t ever recall using AN8 bolts for...

    Yeah I don’t ever recall using AN8 bolts for anything.
  9. Thread: Scott 3200 AN6?

    by KJC
    Replies
    11
    Views
    763

    Yes new AN-7 bolt bolt and new Airframes 1 3/4”...

    Yes new AN-7 bolt bolt and new Airframes 1 3/4” spring. It’s a good 3 leaf spring and gets rid of the adaptor. Also, make sure to grease between the springs. ( Remember they move.). It will help...
  10. Replies
    10
    Views
    4,023

    When you do the one for the jackscrew yoke, make...

    When you do the one for the jackscrew yoke, make sure the top edge is parallel to the upper wood stringer. It will look like it’s tilted aft just slightly in the aft rear corner. Look at the above...
  11. Thread: Scott 3200 AN6?

    by KJC
    Replies
    11
    Views
    763

    Here’s how not to do it. If your missing the 7/16...

    Here’s how not to do it. If your missing the 7/16 bushing, just use a 1/2 bolt and wallow out the spring to make it work. Complete BS job. The bushing is $10. You can see this spring was about 1...
  12. Replies
    14
    Views
    1,084

    I’m pretty good about keeping things organized...

    I’m pretty good about keeping things organized and like parts with like parts. I’m sure this came out of this plane but I’m just drawing a complete blank. It’s something interior…….?
  13. Replies
    14
    Views
    1,084

    It’s out of an -18. Something interior I think....

    It’s out of an -18. Something interior I think. I went to the trouble of priming and painting but I’m drawing a blank. I’m pretty sure it’s not a wing part.
  14. Replies
    14
    Views
    1,084

    Help Identifying a Part

    Any ideas? Like Larry said to Moe, Im thinking but nothings happening.

    59471
  15. Replies
    14
    Views
    885

    Insulation and Soundproofing

    Does anyone have any suggestions on a material for insulation and soundproofing a new/ rebuilt bootcowl? Its a certified-18.
  16. Replies
    20
    Views
    5,187

    So are you using the Day/Night STC and deviating...

    So are you using the Day/Night STC and deviating based on that? I’m curious how this is written up. If you got this done via Field Approval then good on you! Could you post a copy?
  17. Replies
    24
    Views
    6,407

    It’s still sitting in my hanger without much...

    It’s still sitting in my hanger without much progress. I found a small Continental mount for it and removed all the sheet metal for patterns but little else. It’s on my “project list”.
  18. Replies
    1
    Views
    286

    Scott Parking Brake Placard

    Anyone have a source for these new or a used set in better shape than these?

    59148
    59149
  19. Thread: Aileron Design

    by KJC
    Replies
    25
    Views
    1,850

    Stewart- I wish I could convince both the...

    Stewart-
    I wish I could convince both the builders and manufacturers how much better the -12/14 ailerons are. For most of the -18 owners on here who have never flown a -12, be aware that they are...
  20. Thread: Open top Pod ?

    by KJC
    Replies
    9
    Views
    839

    I’m thinking that’s one of Jays airplanes. I’ll...

    I’m thinking that’s one of Jays airplanes. I’ll ask when I see him.
  21. Thread: Open top Pod ?

    by KJC
    Replies
    9
    Views
    839

    Im still trying to figure out how he gets it...

    Im still trying to figure out how he gets it back on with a bunch of dead critters in it
  22. Replies
    22
    Views
    1,478

    Or you could order the 3 notch handle for an A...

    Or you could order the 3 notch handle for an A model from Univair.
  23. Replies
    27
    Views
    12,800

    As long as you make sure the C/L of the tail...

    As long as you make sure the C/L of the tail wheel axle is 14” behind the tail post.
  24. Thread: Summit Skis

    by KJC
    Replies
    61
    Views
    3,720

    How do you sign off Summits on a standard...

    How do you sign off Summits on a standard category airplane? Trickairs are approved. Summits aren’t, right?

    Correct.
  25. Replies
    8
    Views
    941

    PA-12s came from the factory with and without...

    PA-12s came from the factory with and without header tanks. Both versions had 2 valves. Neither version had outlets on the forward side of the tanks. This caused some unporting of the fuel system...
Results 1 to 25 of 336
Page 1 of 14 1 2 3 4