Search:

Type: Posts; User: Steve Pierce

Page 1 of 20 1 2 3 4

Search: Search took 2.55 seconds.

  1. Replies
    1
    Views
    86

    PA12 For Sale in Texas

    I recently looked at pictures and paperwork and spoke with the owner/restorer of the PA12 in Paige, Texas. Lots of unanswered questions. I would avoid but just my opinion.
  2. Replies
    3
    Views
    356

    I use urethane sealant around the D window to...

    I use urethane sealant around the D window to seal water out. Urethane sticks to polycarbonate better than silicone.
  3. Replies
    16
    Views
    576

    I have been using a manual chain hoist for many...

    I have been using a manual chain hoist for many years. The hanging chain to manipulate the hoist is always in close proximity to the windshield and I know it is only a matter of time. The other thing...
  4. Replies
    2
    Views
    599

    I will gladly keep maintaining this one. A lot...

    I will gladly keep maintaining this one. A lot about keeping it maintained went into this build.
  5. Replies
    16
    Views
    576

    Electric Chain Hoist

    So the new hangar should be here in the next few weeks, door and heat and air unit are here. I figure I am only doing this once and want to try and do it right. The old single point manual chain...
  6. Replies
    5
    Views
    948

    A couple of months thanks to Covid. Filed...

    A couple of months thanks to Covid. Filed 3-12-2021 and signed by the governor on 6-4-2021. https://legiscan.com/TX/bill/HB4436/2021
  7. Replies
    59
    Views
    6,515

    I don't know, you might be pushing the limits of...

    I don't know, you might be pushing the limits of the pilots abilities by throwing in those extra tasks. ;)
  8. Replies
    19
    Views
    5,557

    Like this. 58075

    Like this.
    58075
  9. Replies
    19
    Views
    5,557

    You could do like this guy but looks pretty...

    You could do like this guy but looks pretty amateurish to me. I would just use beaded from the master cylinder to the gear leg and if needed, bottom of gear leg to the caliper. There are Weatherhead...
  10. Replies
    49
    Views
    2,825

    Usually when the diaphragm goes it bursts and...

    Usually when the diaphragm goes it bursts and runs fluid all over the floor board.
  11. Replies
    2
    Views
    599

    1982 PA18 160hp Restored $275K

    I figure the headline will get some attention and start some controversy. This is a 1982 model PA18-150 upgraded to 160 hp. Out of rebuild 2 years at the end of this month and rebuilt LyCon engine...
  12. Replies
    6
    Views
    407

    I made Tal do that. All the others that I have...

    I made Tal do that. All the others that I have done where at rebuild and those tubes are easy to pull out when the cylinder isn't installed.
  13. Replies
    6
    Views
    407

    I saw that, I want the one that shows sold for...

    I saw that, I want the one that shows sold for $35. :lol:
  14. Chris, I know you are a romantic but romance...

    Chris, I know you are a romantic but romance doesn't pay the bills. I am sure you could raise a good bit of money with a Go-Fund me but I doubt it would be as much as you could get for the airplane...
  15. Replies
    5
    Views
    737

    Looks like someone modified a J3 fuselage to me....

    Looks like someone modified a J3 fuselage to me. Door attachment, rear of top deck aft of the wing attachment, rear seat and other structures. Heavily modified.
  16. Replies
    6
    Views
    407

    That is slick. I have installed a lot of those...

    That is slick. I have installed a lot of those kits but have never seen the inside tubing cutter. Gotta find one now. Yes, I am a tool junky. ;)
  17. Replies
    1
    Views
    283

    Sal's Aircraft Cylinders 972-346-3339 Gibson...

    Sal's Aircraft Cylinders 972-346-3339

    Gibson Aviation https://gibsonaviationok.com/
  18. Replies
    34
    Views
    1,234

    Before you do anything find out if it does it...

    Before you do anything find out if it does it again and under what conditions. I had a Super Cub that I had recovered do this after we brought it to Texas from Florida and then it went to the midwest...
  19. Replies
    29
    Views
    11,333

    Look at the Lycoming O-320 Type Certificate Data...

    Look at the Lycoming O-320 Type Certificate Data Sheet and see what the difference in the engine model you have and the one certified on your airplane. A lot of time it is a simple to change the...
  20. Replies
    18
    Views
    848

    Once you got it set up did you find you had to...

    Once you got it set up did you find you had to adjust it again under different conditions. I admit it is a pain to go into the settings and set it up. I did it initially and haven't messed with it...
  21. Replies
    8
    Views
    706

    And the poster promoting the Beringer gear...

    And the poster promoting the Beringer gear groundlooped both his Carbon Cubs with said gear. The one he sold came to my neck of the woods and a very competent instructor I know removed it and put the...
  22. What is the oil consumption? What are the...

    What is the oil consumption? What are the compressions and where is the air leaking? What does a borescope inspection show you? What does inside the valve covers look like? Lyconings don't normally...
  23. Replies
    18
    Views
    848

    Interesting, I have done 3 lately including my...

    Interesting, I have done 3 lately including my own and thought they all sounded great and were easy to set up. Of course Cathy says I can't hear lots of things but I thought that was her just nagging...
  24. Replies
    18
    Views
    1,120

    I have cutouts and play with them on the blank...

    I have cutouts and play with them on the blank panel prior to cutting.
  25. Replies
    18
    Views
    1,120

    Scott, some good layouts here....

    Scott, some good layouts here. https://www.supercub.org/forum/showthread.php?54930-Cgr-30-p
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4