Search:

Type: Posts; User: KJC

Page 1 of 13 1 2 3 4

Search: Search took 0.28 seconds.

  1. Replies
    18
    Views
    1,116

    Yes use the cutouts and play with them to ensure...

    Yes use the cutouts and play with them to ensure you have good clearance for everything behind the panel. Unless you plan on having it laser cut, you’ll also need a knockout punch and template from...
  2. Replies
    6
    Views
    343

    FS: How much for the Borer Prop and exhaust?

    How much for the Borer Prop and exhaust?
  3. Replies
    15
    Views
    953

    Thanks everyone. I’ll be making some phone calls...

    Thanks everyone. I’ll be making some phone calls today.
  4. Replies
    15
    Views
    953

    Having never used the stuff, I’m a bit confused....

    Having never used the stuff, I’m a bit confused. Is it more than just an adhesive backing on the tape? What’s this soap and water squeegee method you speak of? Also, do they shrink after several...
  5. Replies
    15
    Views
    953

    I’m curious if during installation if you can...

    I’m curious if during installation if you can remove it as long as it not pressed on too hard. Sometime it take a couple of try’s to get it perfectly straight. Any brand recommendations?
  6. Replies
    15
    Views
    953

    Vinyl Stripes on a Cub?

    Has anyone used 3M or other vinyl striping on a Cub. Iíd like to run a black 1/4 inch strip on the current project but Iím interested in opinions on the matter first. If I donít use vinyl, itís going...
  7. Replies
    6
    Views
    621

    Four with a full length reinforcing and a two...

    Four with a full length reinforcing and a two inch tape. Don’t use dollar patches. If you expand the picture, you can see before the tape went on. If you don’t stich it the fabric will drum from...
  8. Replies
    4
    Views
    258

    Like this one? I can’t find the manual. Oh and...

    Like this one? I can’t find the manual. Oh and by he way, Divine Providence must be looking out for you because I had this in my hand last week and almost threw it away. I figured they send a new...
  9. Replies
    4
    Views
    258

    I’m pretty sure I have one to loan you. I’ll...

    I’m pretty sure I have one to loan you. I’ll check in the shop this morning.
  10. Replies
    7
    Views
    486

    57666Like this. Same on the round top.

    57666Like this. Same on the round top.
  11. Thread: O-290 oil cooler

    by KJC
    Replies
    5
    Views
    370

    I think I have a used cooler and vernatherm...

    I think I have a used cooler and vernatherm valve. PM if interested. I think it’s the same as the O-320 but not positive.
  12. Replies
    8
    Views
    715

    Sure. 1966 model. 2000#, xbrace, dogleg, weld in...

    Sure. 1966 model. 2000#, xbrace, dogleg, weld in extended baggage, float fittings, belly pod tabs, rear metal belly, L21 windows etc.


    57239
  13. Replies
    8
    Views
    715

    5723257233 Easily done. Thanks.

    5723257233
    Easily done. Thanks.
  14. Replies
    8
    Views
    715

    Awesome!! Thank you very much. That’s what I...

    Awesome!! Thank you very much. That’s what I needed. The gromet under the fabric I can make.
  15. Replies
    8
    Views
    715

    Yes I saw it and posted in it as well. I just...

    Yes I saw it and posted in it as well. I just want to be sure before I go cutting and gluing.
  16. Replies
    8
    Views
    715

    Original Piper Brake Line Exit

    572275722557226
    Iíve asked about this before and Iím still not quite understanding how Piper had the brake lines exit the fuselage. Iím hoping to keep them inside and exit just behind the front gear...
  17. Replies
    12
    Views
    968

    Unless someone comes up with a good reason, I’m...

    Unless someone comes up with a good reason, I’m going to put the deflectors in front of the grommets and hold the grommets in place with black RTV on the underside so it won’t show. Between that and...
  18. Replies
    12
    Views
    968

    I called Atlee today and Justin couldn’t remember...

    I called Atlee today and Justin couldn’t remember how he did it in his Cub but will get some pictures this evening. I usually try and follow the directions, but I don’t see why you can’t use silicone...
  19. Replies
    12
    Views
    968

    Attlee Defroster Install Question

    Do these deflector brackets really get mounted on top of the hole like the directions say or am I reading them wrong? Could the possibility go in front?

    5665856659
  20. Replies
    10
    Views
    857

    I have no idea what you mean. The above photos...

    I have no idea what you mean. The above photos are of a stock door with a Lexan cover. That gas piston works perfectly.
  21. Replies
    10
    Views
    857

    This is the rod you need. Note the part number....

    This is the rod you need. Note the part number. Order the ball sockets with the rod. You need to fabricate the brackets out of stainless. Make sure you install the gas piston at the top. It easily...
  22. Thread: PA-12 Seat Adjust?

    by KJC
    Replies
    8
    Views
    840

    Here’s a pic of a modification I had on my last...

    Here’s a pic of a modification I had on my last -12. Joggles the seat back about 2-3 inches. Worked great and was very comfortable for a 6’2’ 240# guy. Some welding involved but cheeped than a...
  23. Replies
    4
    Views
    820

    Paul how’s retirement going?

    Paul how’s retirement going?
  24. Replies
    35
    Views
    4,872

    Interesting thread. Glad your ok Steve. Checked...

    Interesting thread. Glad your ok Steve. Checked the one in the shop with a newer valve that’s less than a year old. No Loctite.

    56184
  25. Replies
    0
    Views
    297

    Cleveland 40-60 6 Bolt Wheels

    I have two sets of 40-60 Cleveland Wheels with 1.25 axles. One is in very good shape the other is like new. Tires in the photo are not included. $1200 for the one set, $1500 for the other. Compare to...
Results 1 to 25 of 303
Page 1 of 13 1 2 3 4