Search:

Type: Posts; User: Kahles56

Page 1 of 4 1 2 3 4

Search: Search took 0.02 seconds.

  1. Thread: PA12 flaps

    by Kahles56
    Replies
    33
    Views
    2,359

    My plans state that the flaps are (65 and 5/16 ")...

    My plans state that the flaps are (65 and 5/16 ") Obtained from Piper plan # 11686, Drawing dated 01/22/1948 By RTM, checked 01/23/1948 By MRK.
  2. Replies
    31
    Views
    3,952

    An Aeromatic hub with modern carbon fiber blades...

    An Aeromatic hub with modern carbon fiber blades would fit the bill, now to find or build carbon fiber blades I have the hub for a a2b 320.
    Another project , Dam!
  3. Replies
    849
    Views
    541,166

    :new_rofl::new_rofl::new_rofl::new_rofl:

    :new_rofl::new_rofl::new_rofl::new_rofl:
  4. Thread: PA12 flaps

    by Kahles56
    Replies
    33
    Views
    2,359

    I purchased PA -14 flaps and supporting hardware....

    I purchased PA -14 flaps and supporting hardware.
    I have to use the Mardin plans to install due to the flap seat/handle and cable routing.
    The flaps are PMA flaps made from piper drawings.
    From...
  5. Thread: PA12 flaps

    by Kahles56
    Replies
    33
    Views
    2,359

    The answer is yes My kit from Dakota includes...

    The answer is yes
    My kit from Dakota includes flaps, hangers, false spars, bell-cranks, pushrods.
    Control cable standoffs--? cannot remember,

    My understanding is there are multiple ways to run...
  6. Thread: PA12 flaps

    by Kahles56
    Replies
    33
    Views
    2,359

    Dakoda cubs sells PA 14 flaps, hangers and they...

    Dakoda cubs sells PA 14 flaps, hangers and they are PMA, I know because I bought a set.
    I am in process of deciphering the notes on the Marden drawings, having a hard time with them as my copy is so...
  7. If you are going to use the HF spray gun, go on...

    If you are going to use the HF spray gun, go on you tube and see what you need to do to make preform.
    I use one for spraying primer only. I had to tear it apart and clean before I used it as I found...
  8. Replies
    29
    Views
    2,090

    I do not know pertaining to the stoichiometric...

    I do not know pertaining to the stoichiometric mixture, this is because I am not a chemical engineer.
    Your "richer " question I cannot answer, however you are asking in effect an orange vs....
  9. Replies
    29
    Views
    2,090

    I stand corrected, 2/3 the BTU of Gas. Since...

    I stand corrected, 2/3 the BTU of Gas.

    Since we utilize a BTU Money to Noise generator in our older aircraft, a BTU is a BTU, unless Physics and thermodynamics has changed from the 70's/80's and...
  10. Replies
    29
    Views
    2,090

    Ethanol is just a filler, so gas companies do not...

    Ethanol is just a filler, so gas companies do not have to provide a full gallon of gas.
    The BTU value of ethanol is 1/2 of gas so for every 10% of ethanol used you lose 5% in fuel economy.
    Ethanol...
  11. Replies
    14
    Views
    1,553

    Need some closer pictures and at different...

    Need some closer pictures and at different angles, however it looks as an intermediate crossover lever for flap wires.?

    Is this out of a PA-12 with Flaps and came as a basket case?
  12. Replies
    32
    Views
    3,164

    If / when when they figured out who you are/were,...

    If / when when they figured out who you are/were, and they would find you out, or hunt you down on YouTube, you would do more damage to GA than the idiot who jumped out of the Stenson in California a...
  13. Replies
    20
    Views
    2,670

    Too cool, Can you get the name of the APP .I...

    Too cool, Can you get the name of the APP .I would like to have it to use.
    Thanks,
    Ken
  14. This is exactly what I was looking for., Yes it...

    This is exactly what I was looking for., Yes it is a Super Cruiser rebuild. I should have stated that in the first post.
  15. locating correct elevation points of front spar and rear spar .

    All,
    I have tried to search for information on the correct elevation differences between the front and rear spar. My plans do not have the sizes for the spars.
    I need this to check my attachment...
  16. This for a A, I think I saw one at a friends...

    This for a A,
    I think I saw one at a friends house where the frame was wrapped around a tree on landing/ if you want to call it that.
    The craft still has the hopper in side with the hatch on top....
  17. Replies
    52
    Views
    8,719

    Get a giant Wiley Coyote doll and add some weight...

    Get a giant Wiley Coyote doll and add some weight to him , Place in back seat and strap him in .
    I saw that one on the back of a Harley one time , Dam near wrecked my truck I was laughing so hard, ...
  18. Replies
    87
    Views
    14,725

    It is a Fabric Pro Iron, I just got one over the...

    It is a Fabric Pro Iron, I just got one over the holidays, took 3 days to get it from California. Really fast shipping

    It is a first class iron, comes with a case that you store it in even if semi...
  19. Thread: Plug cleaners

    by Kahles56
    Replies
    14
    Views
    2,716

    Check Craig's list, hear in the Carolinas they...

    Check Craig's list, hear in the Carolinas they come up every few months or so for $100.00 to $200.00.
    I picked up a AC Delco ( they were all made by the same company and minor items were done for...
  20. Replies
    51
    Views
    7,961

    i like the part of finishing the bottle of wine,...

    i like the part of finishing the bottle of wine, I would have done that procedure first to allow me to control my nerves with that hole saw!:roll:
  21. Replies
    97
    Views
    22,133

    Is that a cabin controlled Aeromatic Propeller?

    Is that a cabin controlled Aeromatic Propeller?
  22. Replies
    18
    Views
    3,338

    Mike, Thanks for the answer on Acetylene. On...

    Mike, Thanks for the answer on Acetylene.

    On another question i am asking,
    has anyone, does anyone have a STC mod to drill through the crankcase to add piping to allow oil to hit the cam-lobes...
  23. Replies
    18
    Views
    3,338

    Mike, Thanks for the answer on Acetylene.

    Mike, Thanks for the answer on Acetylene.
  24. Replies
    18
    Views
    3,338

    I just remembered something , or maybe not . ...

    I just remembered something , or maybe not .
    You professional welders out there, there is one of the gases they fill the tanks up with sawdust then put the gas in it . this is because the gas is...
  25. Replies
    18
    Views
    3,338

    Try a Mylar Balloon taped to the exhaust pipe, on...

    Try a Mylar Balloon taped to the exhaust pipe, on second thought there's no way to seal these engines , to many cracks in exhaust system, gaps in rings, valve stem allowances,
    gaskets leaking etc....
Results 1 to 25 of 78
Page 1 of 4 1 2 3 4