Search:

Type: Posts; User: skywagon8a

Page 1 of 20 1 2 3 4

Search: Search took 0.19 seconds.

  1. That is why I like a direct reading oil pressure...

    That is why I like a direct reading oil pressure gauge.
  2. Replies
    9
    Views
    3,865

    It's easy to make your own. Most any aluminum...

    It's easy to make your own. Most any aluminum sheet will do. Try to avoid the soft stuff.
  3. With my Brownie box camera? That would have been...

    With my Brownie box camera? That would have been more entertaining had there been some of today's modern camera equipment handy. Like Farmboy's 360 degree swivel camera.
  4. Long long ago in the land of Boston's outer...

    Long long ago in the land of Boston's outer harbor I spotted a carrier outbound under tow. Hmmmm? :evil: :evil: :evil: Yes? No? Yess! Line up on final approach, start to engage brain, Hmmm? What if...
  5. Replies
    797
    Views
    465,254

    Can't you just mount a mirror on your crane boom...

    Can't you just mount a mirror on your crane boom which you can see from the Cab? Maybe paint a couple of stripes on it for alignment purposes?
  6. Replies
    162
    Views
    35,103

    4-88. a. Page 4-59 a. Brazing requires less...

    4-88. a. Page 4-59
    a. Brazing requires less heat than welding and can be used to join metals that are damaged by high heat. However, because the strength of brazed joints is not as great as welded...
  7. Replies
    622
    Views
    165,017

    Charlie, You need one of these. It makes nice...

    Charlie, You need one of these. It makes nice clean cuts right through the middle of a sheet without distortion.

    59441
  8. Replies
    162
    Views
    35,103

    Without looking it up, from A&P school memory the...

    Without looking it up, from A&P school memory the rule was not to braze on primary structure. Meaning if it failed it could cause serious failure of the structure. But it was alright to braze...
  9. Just route the fuel lines so the low point is aft...

    Just route the fuel lines so the low point is aft of the rear of the belly pod.
  10. Replies
    7
    Views
    570

    How did they each bend one rotor blade?

    How did they each bend one rotor blade?
  11. Thread: Sonic Booms

    by skywagon8a
    Replies
    3
    Views
    363

    tsunami...

    tsunami advisoryhttps://abcnews.go.com/US/tsunami-warning-issued-us-west-coast-alaska/story?id=82282242
  12. I hear you. However, when in the process of...

    I hear you. However, when in the process of twisting, the person doing the twisting ought to be able to feel a weak tube fracturing. The level of the resistance should be felt.
  13. Wouldn't now be a good time to find any...

    Wouldn't now be a good time to find any corrosion? ................... on the ground!
  14. Before you start persuading it, check the...

    Before you start persuading it, check the stabilizers for alignment. It could be a little of both elevators and stabilizer.
  15. Replies
    36
    Views
    1,410

    I bought a new wood spar from Bellanca for a 7GCB...

    I bought a new wood spar from Bellanca for a 7GCB which was made of four short pieces of spruce scarf spliced end to end without gussets instead of being one long piece. There wasn't any mention of...
  16. Replies
    23
    Views
    905

    You really ought to attend an FAA IA renewal...

    You really ought to attend an FAA IA renewal meeting (When they have a full blown meeting) and pay attention to what FAA "Legal" has to say.
  17. Replies
    96
    Views
    13,189

    I can't supply an engineering source, however I...

    I can't supply an engineering source, however I do know there are several considerations in the design of augmenter exhaust systems. Such as the diameter of the exhaust pipes, the diameter of the...
  18. That makes sense. You didn't mention originally...

    That makes sense. You didn't mention originally that the truck driver spoke to the engineer. Under the circumstances, had I been the engineer, I think I may have done the same thing.
  19. Since you haven't shown the 1st page of the STC,...

    Since you haven't shown the 1st page of the STC, I'll assume the rest of what you've shown is part of it. With that assumption the drawing shown is the proper approved drawing. Using this drawing you...
  20. Interesting thought on this. Assume sitting in...

    Interesting thought on this. Assume sitting in that truck as the train is approaching. Wouldn't that sound automatically get louder the closer the source of the sound got to the ears of the truck...
  21. Replies
    41
    Views
    2,766

    Eaa's Amateur-Built Aircraft Certification kit...

    Eaa's Amateur-Built Aircraft Certification kit will be useful in answering these questions. Also all necessary forms are included. You are the manufacturer and serial number picker....
  22. Without telling us why, are you not able to get...

    Without telling us why, are you not able to get the Basic Med?
  23. Replies
    23
    Views
    905

    "(2) Parts produced by an owner or operator for...

    "(2) Parts produced by an owner or operator for maintaining or altering their own productand which are shown to conform to FAA-approved data"
    Page 2...
  24. Replies
    23
    Views
    905

    It's only an "owner produced part" if it's made...

    It's only an "owner produced part" if it's made in accordance with the approved drawings. An "owner produced part" is a method for the owner to make his own part in lieu of purchasing a Parts...
  25. They don't even slow down when there is something...

    They don't even slow down when there is something on "their" tracks.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4