View Profile: LMartin - SuperCub.Org

Yesterday, 01:02 PM

Bill Rusk replied to a thread Javron covering kit in Experimental Cubs

KJC I have used Stewart’s glue underneath the Airtech primer and paint, and it works beautifully. Bill

32 replies | 1137 view(s)

Yesterday, 12:26 PM

Bill Rusk replied to a thread Javron covering kit in Experimental Cubs

I like and use the Airtec system. It is acetone based rather than MEK based. The MSDS for MEK is 17 pages. The MSDS for Acetone is one page. ...

32 replies | 1137 view(s)

Yesterday, 12:07 PM

Bill Rusk replied to a thread Javron covering kit in Experimental Cubs

My opinion only...... Oratex is simply not attractive and rapidly gets worse with age. The tapes have a sharp edge (like putting a piece of duct...

32 replies | 1137 view(s)

01-28-2023, 08:44 PM

Bill Rusk replied to a thread Building a 4 Seat (4S) Javron Cub in Member Projects in Progress

ENGINES After much consideration we ended up going with a Penn Yan rebuilt 0-360. Penn Yan has a long history and an excellent reputation and it...

83 replies | 16531 view(s)

01-28-2023, 08:31 PM

Bill Rusk replied to a thread Building a 4 Seat (4S) Javron Cub in Member Projects in Progress

This is a general look at the what the removable rear seats look like. When they are not in place the rear cargo area is completely flat with no...

83 replies | 16531 view(s)

01-28-2023, 08:19 PM

Bill Rusk replied to a thread Building a 4 Seat (4S) Javron Cub in Member Projects in Progress

Folks The fuselage is in the hangar and we have started to look at it. This is what the floor mounted style rudder pedals look like. We will...

83 replies | 16531 view(s)

01-27-2023, 02:32 PM

Bill Rusk replied to a thread Good article on grease in Cafe Supercub

Interesting. I thought the Aeroshell 22 was terrible on amphibious float wheel bearings. It very quickly became an emulsified mess and the bearings...

9 replies | 821 view(s)

01-26-2023, 10:37 AM

Bill Rusk replied to a thread Montana Aviation Conference 2023 in Cafe Supercub

I am all registered and signed up for the conference. If going you need to make the hotel reservation prior to Feb 1st to get the conference rate....

6 replies | 731 view(s)

01-24-2023, 11:50 PM

LMartin replied to a thread Montana Aviation Conference 2023 in Cafe Supercub

I might be able to make that. I love the Montana gathering. Sent from my iPad using SuperCub.Org

6 replies | 731 view(s)

01-24-2023, 08:19 AM

LMartin replied to a thread Leading edge screws in Tips and Tricks

Thank you. This was the old tank bay piece. I thought about reinforcing it, the sheet metal the backplate attaches to is pretty worn out, but decided...

14 replies | 1384 view(s)

01-23-2023, 09:34 AM

Bill Rusk replied to a thread Bushwheel Bill is Down But Not Out! in Cafe Supercub

Bill and Diana…..Two of the finest people I know. God is with you, and many are praying. We want to see you well and living life again soon. Get well...

8 replies | 1422 view(s)

01-22-2023, 03:47 PM

LMartin replied to a thread Leading edge screws in Tips and Tricks

Now…installing false spar and skin behind the tank bay. There’s a backplate inside at the flap bell crank. I left my parts book at home. Do I need...

14 replies | 1384 view(s)

01-15-2023, 06:37 PM

Bill Rusk replied to a thread Where did you fly today? in Cafe Supercub

I always love your photos. Thank you Brad. That overflow looks pretty nasty. Bill

1653 replies | 587700 view(s)

01-14-2023, 12:03 PM

LMartin replied to a thread New spar flap hinges in Tips and Tricks

Thanks for the picture story! What do you use to attach the hanger to the false spar? They were mostly rivets when I drilled them out to clean the...

13 replies | 6668 view(s)

01-14-2023, 10:25 AM

LMartin replied to a thread Leading edge screws in Tips and Tricks

Thank you! Sent from my iPhone using SuperCub.Org

14 replies | 1384 view(s)

01-13-2023, 07:43 PM

LMartin replied to a thread Leading edge screws in Tips and Tricks

How about the little #4 machine screws with split washers and hex nuts that attach brace channel to ribs?

14 replies | 1384 view(s)

01-13-2023, 01:48 PM

Bill Rusk replied to a thread Cessna 180 Float Kit Install in Cafe Supercub

Congrats Zack!! If anyone can do this and make it better than factory you are the one. By the way......need you to drop off that seat to Jay...

27 replies | 1113 view(s)

LMartin
Lisa Martin

Mini Statistics

More 1 Friend

Bill Rusk

Recent Visitors

Basic Information

About LMartin

Contact

Statistics

Total Posts

General Information

1 Friend

Bill Rusk

02-06-2023

02-02-2023

01-27-2023

01-25-2023

01-24-2023

01-19-2023

01-16-2023

01-14-2023

LMartin Lisa Martin

Mini Statistics

More 1 Friend

Bill Rusk

Recent Visitors

Basic Information

About LMartin

Contact

Statistics

Total Posts

General Information

1 Friend

Bill Rusk

02-06-2023

02-02-2023

01-27-2023

01-25-2023

01-24-2023

01-19-2023

01-16-2023

01-14-2023

LMartin
Lisa Martin