View Profile: cubdriver2

Yesterday, 11:33 AM

cubdriver2 replied to a thread Mogas/HP/Compression/Timing/Operating Cost in Cafe Supercub

But I seem to remember you having a stuck valve on your Pa11? Glenn

34 replies | 1157 view(s)

01-16-2021, 03:34 PM

cubdriver2 replied to a thread Mogas/HP/Compression/Timing/Operating Cost in Cafe Supercub

The ignition system on newer snow machines automatically adjust to whatever fuel is put in it. Ex Cub should be able to do the same? Glenn

34 replies | 1157 view(s)

01-16-2021, 10:07 AM

cubdriver2 replied to a thread Mogas/HP/Compression/Timing/Operating Cost in Cafe Supercub

Using MMO is by choice, I have never had a stuck valve. And those around me running it in little C engine haven't either. I picked up an old 3.5hp...

34 replies | 1157 view(s)

01-16-2021, 09:47 AM

cubdriver2 replied to a thread Mogas/HP/Compression/Timing/Operating Cost in Cafe Supercub

8a Pete, I forgot about my Stearman R680 time. Add 1700+ gal of 87 Oct from 6 gal cans that held 7gals. I fueled it by myself, long way up to top...

34 replies | 1157 view(s)

01-16-2021, 12:17 AM

cubdriver2 replied to a thread Mogas/HP/Compression/Timing/Operating Cost in Cafe Supercub

23,000+ gallons, savings?8) I could be flying 3 cubs instead of 2 Glenn

34 replies | 1157 view(s)

01-15-2021, 11:53 PM

cubdriver2 replied to a thread Mogas/HP/Compression/Timing/Operating Cost in Cafe Supercub

Love mogas, 23,000+ gallons so far. Plugs last 800 hrs. 8.6 compression. What's not to like? Glenn

34 replies | 1157 view(s)

01-14-2021, 11:22 PM

cubdriver2 replied to a thread TCM C90 Push Rod Tube Leakage in Modifications

That's the one I was looking for when I posted the other picture. This is the one Dan used on his C85 in his J3. Stopped the leak Glenn

9 replies | 367 view(s)

01-14-2021, 06:41 PM

cubdriver2 replied to a thread TCM C90 Push Rod Tube Leakage in Modifications

You can buy a tool like this to expand the loose tube while on the engine buy just pulling the pushrod and rocker. But if you cleaned it good...

9 replies | 367 view(s)

01-14-2021, 10:26 AM

cubdriver2 replied to a thread HDHP: Dr. Randy Corfman - 98.6 Winter Survival Medicine - Tonight! 1-13-21 in Supercub Gatherings

Did Randy jump in and demonstrate the technique? Glenn

9 replies | 481 view(s)

01-13-2021, 07:37 PM

cubdriver2 replied to a thread Glenn Guilfoyle takes his Annual Dip in Cafe Supercub

Ummm. It was dark Glenn

11 replies | 685 view(s)

01-13-2021, 04:49 PM

cubdriver2 replied to a thread Glenn Guilfoyle takes his Annual Dip in Cafe Supercub

One of my favorite places in the whole world. Amy was supposed to go swimming with us there a few years back but chickened out. Maybe the water being...

11 replies | 685 view(s)

01-12-2021, 07:05 PM

cubdriver2 replied to a thread Phillips 66 X/C SAE 20W50 Use in Honda CRF450L motor? in Cafe Supercub

We had a Beech 18 around here that had the DEC/ENCON approved equipment installed with the appropriate brick under both engines Glenn

26 replies | 2111 view(s)

01-11-2021, 03:14 PM

cubdriver2 replied to a thread C130 too close and no radio contact in Take Action Jackson

One of the coolest and scariest was when I was heading home into a setting sun with a bug obscured dirty windshield at about 1200' 15 miles west of...

54 replies | 2812 view(s)

01-11-2021, 08:56 AM

cubdriver2 replied to a thread C130 too close and no radio contact in Take Action Jackson

We have an Air guard base 30 miles East of me and right in the middle of where we all play some days. Been that way for a long time. Some of our...

54 replies | 2812 view(s)

01-08-2021, 11:45 PM

cubdriver2 replied to a thread Beringer ALG vs. Acme Aero for FX3 in CubCrafters: CC18, CC11, CC19 Top Cub, Carbon Cub, and X-Cub

I do love my T3, 1930s Tiger Moth TW inovation re-invented Glennis

307 replies | 19660 view(s)

01-07-2021, 06:06 PM

cubdriver2 replied to a thread Super cub with O-320 blue prints in Piper: PA-18 Super Cub (and L18C & L21)

No two are the same Glenn

9 replies | 592 view(s)

01-05-2021, 09:49 PM

cubdriver2 replied to a thread Distractions in the Cockpit in Cafe Supercub

Did you do any research to find out if Clyde is related to Douten? :pop: Glenn

4 replies | 631 view(s)

01-05-2021, 08:02 PM

cubdriver2 replied to a thread Brake Fluid PA18 -150 in Tips and Tricks

Most likely Dot3 brake fluid. It destroys paint and some rubber. Glenn

19 replies | 1068 view(s)

01-05-2021, 08:01 PM

cubdriver2 replied to a thread Brake Fluid PA18 -150 in Tips and Tricks

All Piper J4 used automotive brake fluid. Master cylinders were car wheel cylinders. I have had to change out an expander tube on my J4 but all of my...

19 replies | 1068 view(s)

01-04-2021, 10:53 PM

cubdriver2 replied to a thread Pirep on Summit Skis in Ski Flying Forum

Dave understands the system better then anyone I've ever seen. In his spare time he helps keep Rhinebeck alive Glenn

34 replies | 1580 view(s)

01-04-2021, 11:29 AM

cubdriver2 replied to a thread Pirep on Summit Skis in Ski Flying Forum

Oops, cost less, quality is superb. Summits are 5K to over 7K Glenn

34 replies | 1580 view(s)

01-04-2021, 12:07 AM

cubdriver2 replied to a thread Pirep on Summit Skis in Ski Flying Forum

Summits are a great ski. But with limited HP on a short strip there were days where I couldn't get out and a couple times I was lucky to get back to...

34 replies | 1580 view(s)

01-02-2021, 10:54 PM

cubdriver2 replied to a thread PA-11 C85-12 Prop recommendations in Piper: PA-11 Cub Special (and L-18B)

What prop are you flying now? Glenn

12 replies | 675 view(s)

01-02-2021, 10:49 PM

cubdriver2 replied to a thread Has anyone shipped floats within the last few years? in Float Operations

I used some muffler type clamps to attach 2- 2x6x8s to my factory cross rack then screwed 2-2x6x12 on the ends perpendicular to them, screwed a 2x2...

23 replies | 1485 view(s)

01-02-2021, 03:34 PM

cubdriver2 replied to a thread Tail ski mount in Ski Flying Forum

My T3 API home made wheel ski Glenn

29 replies | 2061 view(s)

01-02-2021, 12:23 AM

cubdriver2 replied to a thread PA-11 C85-12 Prop recommendations in Piper: PA-11 Cub Special (and L-18B)

Welcome, climb? Cruise? Midrange? What are you trying to improve? Glenn

12 replies | 675 view(s)

01-01-2021, 04:58 PM

cubdriver2 started a thread Hydrosorbs in Parts and Pieces

My buddy Ray discovered these on his Pa11 he bought last year. HD bungees. He wants to go back to standard 11 gear Asking $700 Ray's...

0 replies | 242 view(s)

01-01-2021, 04:39 PM

cubdriver2 replied to a thread Cruise prop and climb prop pitch for C90-12 in Cafe Supercub

Jim if you have a 50 I'd like to try it. I ran a 52 pitch for the last 2 + years but now have the 48 in for skis. They make keys from 32" to 60" in...

34 replies | 1469 view(s)

01-01-2021, 10:09 AM

cubdriver2 replied to a thread Cruise prop and climb prop pitch for C90-12 in Cafe Supercub

Pete, first time I saw that prop on a plane was on Mike Harts Legend Cub up on the Ramp at Greenville Me. That was also the first time I met Mike....

34 replies | 1469 view(s)