View Profile: Utah-Jay - SuperCub.Org

Tab Content: All; Utah-Jay; Friends; Photos

Older Activity
05-04-2021, 09:21 AM

Utah-Jay replied to a thread Registering new airstrip with FAA in Cafe Supercub

I have you in my flight plan for June 21st, I will do a fly over on my way to KSMN to do a day of mountain flying with Dick Williams. I will drop...

see more

12 replies | 626 view(s)
04-28-2021, 09:23 AM

Utah-Jay replied to a thread Trim/CG configuration for Landing? in Cafe Supercub

Thanks. The first landing was the 1st one trying some new stuff so I was not really dialed in. I learned a lot form the 1st landing and improved...

see more

19 replies | 1155 view(s)
04-27-2021, 10:45 AM

Utah-Jay replied to a thread Trim/CG configuration for Landing? in Cafe Supercub

Here is a video with the fruits of my “labor”. Got up early to practice a bit. Last touchdown was at 43mph IAS which is my stall, the other two...

see more

19 replies | 1155 view(s)
04-23-2021, 11:43 AM

Utah-Jay replied to a thread Remote Cabin / Portable High Speed Internet Beta - Tesla in the Sky - Starlink in Cafe Supercub

160 MBPS is pretty darn good, especially for under a $100

see more

28 replies | 1457 view(s)
04-22-2021, 11:02 PM

Utah-Jay replied to a thread Trim/CG configuration for Landing? in Cafe Supercub

Firstly, thanks for all the help! I went out early this morning and worked on stalls (again!!!!) and then as suggested extremely slow flight...

see more

19 replies | 1155 view(s)
04-22-2021, 10:49 PM

Utah-Jay replied to a thread Trim/CG configuration for Landing? in Cafe Supercub

I am practicing well under gross, guessing about 400# under gross

see more

19 replies | 1155 view(s)
04-22-2021, 10:48 PM

Utah-Jay replied to a thread Trim/CG configuration for Landing? in Cafe Supercub

Prop diameter and pitch are very similar, the 20 had a Rotax 912, the 21 has a 915.

see more

19 replies | 1155 view(s)
04-21-2021, 02:19 PM

Utah-Jay replied to a thread Trim/CG configuration for Landing? in Cafe Supercub

That is the plane for tomorrow, crappy is weather today with 12-20 crosswinds

see more

19 replies | 1155 view(s)
04-21-2021, 02:14 PM

Utah-Jay replied to a thread Trim/CG configuration for Landing? in Cafe Supercub

MTV Last question first, I have done a lot (over 20) of stalls and it stalls at 43-44mph every time with either 3 or 4 notches of flaps. 48 with...

see more

19 replies | 1155 view(s)
04-21-2021, 11:16 AM

Utah-Jay replied to a thread Trim/CG configuration for Landing? in Cafe Supercub

I did slow it down yesterday, I was about 5-7mph above stall on short final and it was better. I am clueless about trim helping for landings, hence...

see more

19 replies | 1155 view(s)
04-21-2021, 11:01 AM

Utah-Jay started a thread Trim/CG configuration for Landing? in Cafe Supercub

I am sure this will illicit a bunch of responses... but I am looking for some help here. I have read various posts over time about setting trim for...

see more

19 replies | 1155 view(s)
04-20-2021, 07:02 PM

Utah-Jay replied to a thread Where did you fly today? in Cafe Supercub

Will do

see more

1083 replies | 239192 view(s)
04-20-2021, 06:02 PM

Utah-Jay replied to a thread Where did you fly today? in Cafe Supercub

Dave it is the Rotax 915. It is also the early long wing (30’) as opposed to the 28’ that is in production.

see more

1083 replies | 239192 view(s)
04-20-2021, 05:25 PM

Utah-Jay replied to a thread Where did you fly today? in Cafe Supercub

Well, I did not fly anywhere today, but I did punch some holes in the sky. Still working on getting comfortable in the Rans S-21 after learning in...

see more

1083 replies | 239192 view(s)

No More Results

Utah-Jay

Mini Statistics

Recent Visitors

Basic Information

About Utah-Jay

Signature

Statistics

Total Posts

General Information

05-16-2021

05-13-2021

05-11-2021

05-10-2021

05-04-2021

05-03-2021

05-02-2021

04-28-2021

04-27-2021

04-26-2021