View Profile: motosix - SuperCub.Org

Tab Content: All; motosix; Friends; Photos

Older Activity
04-08-2021, 10:47 PM

motosix replied to a thread FS: Universal hangers in Parts and Pieces

ABS, PLA, PETg, ??

see more

5 replies | 285 view(s)
04-05-2021, 11:26 AM

motosix replied to a thread Bushwheels in Piper: J-3 Cub (and L-4)

3 PSI is my favorite as well, but for a 29" airstreak holding up a 850#(ish) Cub. The only time it is higher is to make it easier to push around the...

see more

58 replies | 4321 view(s)
04-05-2021, 09:55 AM

motosix replied to a thread Leading edge slats and Keller Flaps in Experimental Cubs

Stewart -- How did you set the size of the exit area on your slat? Does your generation slat use the single through hole in the slat hanger with a...

see more

20 replies | 999 view(s)
04-01-2021, 11:02 AM

motosix replied to a thread Bushwheels in Piper: J-3 Cub (and L-4)

Tom -- what peak is that just behind the right shoulder of your landing area?

see more

58 replies | 4321 view(s)
04-01-2021, 09:57 AM

motosix replied to a thread Bushwheels in Piper: J-3 Cub (and L-4)

None handy, but easy enough to describe: Take one of these:...

see more

58 replies | 4321 view(s)
03-31-2021, 10:53 AM

motosix replied to a thread Bushwheels in Piper: J-3 Cub (and L-4)

If they made 31" Airstreaks, I would buy them in a heartbeat. Until then, another J3(ish) on 29s: (I use mesh cargo net above the rear...

see more

58 replies | 4321 view(s)
03-19-2021, 03:17 PM

motosix replied to a thread Building an Experimental PA11 in Experimental Cubs

I am at 1310lbs GW too and run the Univair J3 struts on my little bird. Any idea of the weight savings between the stock J3 and your new aluminum...

see more

236 replies | 36150 view(s)
03-18-2021, 11:52 AM

motosix replied to a thread Building an Experimental PA11 in Experimental Cubs

I can't wait to see how these go together for you.

see more

236 replies | 36150 view(s)
03-12-2021, 05:11 PM

motosix replied to a thread Alaska GarminPilot /ForeFlight revisited in Cafe Supercub

Even though he uses Foreflight, I suppose that Ted guy is all right after all... :D

see more

12 replies | 996 view(s)
03-11-2021, 04:04 PM

motosix replied to a thread Measurement Verification? in Experimental Cubs

I really appreciate that, Jerry. 6.25" is what I expected it should be. I do seem to have a version that is ~7.45 to the firewall but not sure if it...

see more

3 replies | 423 view(s)
03-11-2021, 03:17 PM

motosix replied to a thread Alaska GarminPilot /ForeFlight revisited in Cafe Supercub

I always found that pretty annoying too. I am on Android which lags a bit behind the iOS offering for Pilot. Even worse, my tablet is on the older...

see more

12 replies | 996 view(s)
03-11-2021, 01:55 PM

motosix replied to a thread Alaska GarminPilot /ForeFlight revisited in Cafe Supercub

Garmin can import user waypoints from CSV now. For trip planning Foreflight might have the edge, but like others have previously pointed out, I too...

see more

12 replies | 996 view(s)
03-11-2021, 12:34 PM

motosix started a thread Measurement Verification? in Experimental Cubs

I would greatly appreciate it if someone could verify a measurement for me? I am looking for the rough distance from the top of a dynafocal engine...

see more

3 replies | 423 view(s)

No More Results

motosix

Mini Statistics

Recent Visitors

Basic Information

Statistics

Total Posts

General Information

04-08-2021

04-05-2021

04-02-2021

04-01-2021

03-31-2021

03-28-2021