View Profile: Gordon Misch

Today, 01:45 AM

Gordon Misch replied to a thread Insurance for a Carbon Cub in Cafe Supercub

Wealthy plus proud equals likely trouble. Glenn is one to listen respectfully to.

49 replies | 954 view(s)

Today, 12:12 AM

Gordon Misch replied to a thread Where did you fly today? in Cafe Supercub

Southbound between Bremerton and Olympia, Wa yesterday.

984 replies | 202781 view(s)

01-19-2021, 12:12 AM

Gordon Misch replied to a thread Slip/Skid in Cafe Supercub

This one is a good follow-on. Slightly different explanation. https://www.youtube.com/watch?v=PMhoPJYCvXA

11 replies | 1008 view(s)

01-15-2021, 11:22 PM

Gordon Misch replied to a thread Mogas/HP/Compression/Timing/Operating Cost in Cafe Supercub

Premium no ethanol here is 91 octane. I use premium mogas with 8.5 pistons, per Peterson STC. I dont notice any performance difference compared...

35 replies | 1424 view(s)

01-15-2021, 11:16 PM

Gordon Misch replied to a thread Who fixes HD gear in Super Cub Repair Facilities

Drop the "2", Windy! Oh wait - never mind, you're young yet.

25 replies | 1146 view(s)

01-14-2021, 11:18 PM

Gordon Misch replied to a thread Fuselage advice in Piper: PA-18 Super Cub (and L18C & L21)

For any bending, buckling or torsional loads, diameter. Pure tension or non-Euler buckling compression, just the cross sectional area of the metal.

23 replies | 1527 view(s)

01-14-2021, 12:04 AM

Gordon Misch replied to a thread Hydrasorb/strut attachment question in Piper: PA-18 Super Cub (and L18C & L21)

Can't tell for sure from the photo, but looks like the bolt holes on the hydrasorb are parallel. They need to be perpendicular to each other. The...

5 replies | 306 view(s)

01-13-2021, 11:45 PM

Gordon Misch replied to a thread Fuselage advice in Piper: PA-18 Super Cub (and L18C & L21)

I agree with paragraphs 1 and 2, but don't understand how hoop stress plays into a tubular steel truss?

23 replies | 1527 view(s)

01-11-2021, 11:55 PM

Gordon Misch replied to a thread Stewart System review in Super Cub Repair Facilities

I know - was just kidding you..

27 replies | 1138 view(s)

01-11-2021, 11:44 PM

Gordon Misch replied to a thread Stewart System review in Super Cub Repair Facilities

Dunno, I've done both and I think each has its advantages. I hated the polyfiber glue, but that was like 40 years ago so probably doesn't mean...

27 replies | 1138 view(s)

01-11-2021, 11:41 PM

Gordon Misch replied to a thread Stewart System review in Super Cub Repair Facilities

"Clocks ticking on your bill at $1.50 a minute......" Run and check your anodizing pot:lol:8)

27 replies | 1138 view(s)

01-11-2021, 09:41 PM

Gordon Misch replied to a thread Stewart System review in Super Cub Repair Facilities

Can't be in a rush with Stewarts. Give it time, and maybe a second coat. Maybe Marty57 will chime in?

27 replies | 1138 view(s)

01-11-2021, 09:06 PM

Gordon Misch replied to a thread Dihedral question in Piper: PA-12 Super Cruiser

Mike's the expert, but I'd add to pick "something" to define as level, and then stick with it. Pick a tube that is pretty straight, so that your...

22 replies | 1161 view(s)

01-11-2021, 08:31 PM

Gordon Misch replied to a thread Dihedral question in Piper: PA-12 Super Cruiser

Rigging instructions. Titled PA-18, but includes PA-12. ...

22 replies | 1161 view(s)

01-11-2021, 06:18 PM

Gordon Misch replied to a thread Dihedral question in Piper: PA-12 Super Cruiser

15 threads showing seems like a lot? Bare minimum thread engagement would be 1.5 diameters, depending on class of thread fit and considering the...

22 replies | 1161 view(s)

01-04-2021, 01:02 AM

Gordon Misch replied to a thread Javron Cub Complete in Experimental Cubs

Greg - who would you recommend for a DAR? PM, if you'd prefer - -

63 replies | 5995 view(s)

01-02-2021, 11:42 AM

Gordon Misch replied to a thread Airframes Wide Body 4" in looking for 3 x 3 gear that fit wide body fuselage in Modifications

A related question - - I'm replacing bungees on my -12 and on disassembly noticed some play at the lower shock strut attachment. I measured the...

23 replies | 1125 view(s)

12-31-2020, 10:26 PM

Gordon Misch replied to a thread Airframes Wide Body 4" in looking for 3 x 3 gear that fit wide body fuselage in Modifications

The forward gear leg travel path and the cabane should be in the same plane. Merely angling the cabane will not accomplish that. The axis of...

23 replies | 1125 view(s)

12-28-2020, 12:54 PM

Gordon Misch replied to a thread Steve's Gascolator in Cafe Supercub

I use a small bend. Impossible to vibrate loose, but easy to remove and reinstall without fatiguing it

69 replies | 16962 view(s)

12-23-2020, 08:35 PM

Gordon Misch replied to a thread Early C-180 fuel selector valve rebuild in Everything Else (formerly:My Other Plane Is A....)

Hydraulics supply houses would have similar in steel, with the correct (JIC) flare angle. I think the question would be the length of the hex...

9 replies | 5541 view(s)

12-22-2020, 11:29 PM

Gordon Misch replied to a thread Fuel sight gauges... in Modifications

Yup, when my Atlee 30.5 sight gages reach empty it gets quiet. I agree that the installation is important, such that the horizontal portion of the...

85 replies | 22653 view(s)

Gordon Misch

Mini Statistics

More 1 Friend

RanchPilot

Recent Visitors

Basic Information

About Gordon Misch

Signature

Statistics

Total Posts

General Information

1 Friend

RanchPilot

01-22-2021

01-20-2021

01-18-2021

01-16-2021

01-15-2021

01-14-2021

01-12-2021