PDA

View Full Version : Tips and Tricks



Pages : 1 2 3 4 5 [6]

  1. Bungee Removal ?
  2. Odyssey Battery in a PA-12
  3. Mounting Bushwheels
  4. Too paint or not to paint
  5. Airframe screws getting loose solution?
  6. Scott 3200 on PA12
  7. Spraying Aluminium Stringers
  8. Duplicating tubin
  9. About greases and lubricants ... Your favorites
  10. Plan to build a bungee installation tool ?
  11. prop rpm
  12. Sutton exhaust and Atlee rear seat Heater STC
  13. Looking for Drum adjustment tips for old 4" (hayes?) brakes
  14. Urethane over Stewart glue.
  15. Aerothane vs Ranthane
  16. PA-18 leveling + W&B
  17. Carb Ice Tactics...
  18. New door seal material
  19. Lubricating PVC valve?
  20. Keller (Perfromance) Flap question. Needing more tension some how??
  21. oshkosh
  22. Cleaning seat covers
  23. How to get Sat Phone weather?
  24. Creeping mixture control
  25. Tach time to Clock time ratio
  26. Stewarts Systems Tapes
  27. Location of inspection cover grommets
  28. Door Frame Assembly
  29. Paint stripper for sheet metal: Best products and practices?
  30. Super Cub Rental Mesa AZ
  31. Leading edge material/specs
  32. Leading Edge Fabric Issues
  33. Cleaning Cannon Plugs
  34. Master Brake Overhaul
  35. Imperial fuel selector maitence
  36. Wing tank fuel site glass - little ball float ?
  37. Securing Aircraft on Frozen Lakes
  38. EAA 3D printing
  39. The Oil Filter Bib
  40. Pa12 poh
  41. Skup's Garage
  42. -18 gear 1 1/4" axel insert also ERZ-8011 Kelly starter part needed
  43. SIRS "Pegasus" panel mount compass
  44. PA14 vs PA12 wing tanks
  45. Moab
  46. L21B Fuel Gauge Rebuild
  47. Star Gloss system
  48. Cowling latch P/N 10816
  49. Tie-Downs and Straps
  50. Calibrating an iron; can you use high temp RTV as the heat sink
  51. Super Cub Creeper
  52. PA18/95 command cables trimming
  53. airplane support
  54. AOSS squeaks
  55. Another why not to use ethanol gas
  56. PA-12 trim creep
  57. Uphill/Downhill landings
  58. trim indicator stuck
  59. 200 rpm Mag drop Bendix left mag
  60. rigging Cub wings
  61. Wing tank sight glass mounting
  62. Superior Air Parts Free Book Offer
  63. Spinner backplate gasket?
  64. Eng. mount to airframe bond
  65. J3 - Left window slider
  66. PA18 wing fuselage rigging
  67. Backcountry Engine Preheat
  68. DA performance how to calculate T/O roll
  69. Battery position PA18-95
  70. Playing with the 3D printer...again
  71. Propeller Paint
  72. Cold oil temp fix needed
  73. Tail Pedestal. Pireps?
  74. Low speed airspeed indicator
  75. How to not mess this up?
  76. Rivet pitch ?
  77. Good Screwdriver Tips
  78. Welding rod question
  79. Fuel Injection Engine Starting
  80. Cad cam
  81. Finding Lycoming Bulletins, Letters and Instructions
  82. Fiber like washers between engine mount brackets and firewall?
  83. Engine Mount with 0 degrees with trust line
  84. How NOT to land and take off in a cross wind
  85. Supercub headliner
  86. 3 inch gear question
  87. Cross over vent between independently vented tanks. Yes? No? Why?
  88. Bushwheel Obstructed Valve
  89. Midgies stuck on my final paint surface
  90. Bungee Covers
  91. Looking to fabricate the lower windshield fairing. Can anyone point me in the right direction.
  92. removing shock cords from PA-12
  93. New spar flap hinges
  94. Supercub and Mogas
  95. Aileron pulley bracket
  96. Torquing prop bolts
  97. C90 Primer layout
  98. How to jack up a Cub
  99. Gojacks
  100. Titan Straps
  101. Lumber without a rack?
  102. steps to make a cowling, and other things
  103. Stewart Hangar 21 Hydrasorb Bungee tool wanted to borrow West Central Florida
  104. Electric Chain Hoist. Anyone have a favorite?
  105. Stabilizer/Elevator rigging
  106. Control Surface Rotator for Painting
  107. Earthquake
  108. Areomatic Propellers question
  109. Flap leading edge fab
  110. Carb temp port plug on MA4 carb.
  111. Shaving tires
  112. Cleaning Aluminum with Soda Blaster, Question
  113. Low cost Hydroforming